Home > Error Code > What Error Code Identifies A Floppy Drive Problem

What Error Code Identifies A Floppy Drive Problem

Contents

Press F10 to save and exit. Contact HP Support for assistance. If it has become completely disconnected you will need to re-connect it. If the floppy drive is not setup properly you may experience read/write errors or the floppy may not work at all. this contact form

Please try the request again. Custom Test Tests a specific device. Turn off the PC, unplug the power cord, then press the Power button. Click Properties.

Ibm Error Codes

Not enough memory or resources. Error message: The disk may be write protected There is a plastic switch on the upper right corner of the disk that can be moved up and down from the back Verify that the floppy cable coming from the motherboard is connected to the back of the floppy drive. Find Solutions, ask questions, and share advice with other HP product owners.

If your computer was purchased after 2001, it probably contains a software program called PC Doctor. Use PC Doctor to help verify floppy drive failures before calling support or repairing the computer. The floppy driver should be detected during plug and play and be reinstalled. Ibm Checkpoint Codes Power Light Problem Description Suggested Resolution Solid green Power is on, and the computer is operating normally.

In the System Properties window, click the Hardware tab. Repeat this process for each card. Unexpected interrupt in protected mode — Run the Dell Diagnostics. Extended Test Performs a thorough check of devices.

Checking the cablesIf you have checked the CMOS settings and the settings are correct, the problem may be a poor connection between the floppy drive and the system board or controller. Parity Error Message Non-system disk error — Remove the floppy disk from the drive and restart your computer. As a computer technician, I rely on documentation to guide me through these types of messages. In Setup, press F5 on the keyboard to load defaults.

How Many Digits Are In A Mac Address?

When the boot device list appears, highlight Boot to Utility Partition and press . This page is rather extensive and will be updated on a regular basis. Ibm Error Codes Be careful to not dislodge the other ribbon cables. 162 Configuration Error Ibm Server X3650 Verify that a power connection is also connected to the back of the floppy drive.

Use the HP support document Using PC Doctor to learn more about testing for floppy drive failures. http://3cq.org/error-code/what-is-error-code-105-on-sky.php Insert another floppy disk into the floppy drive and try to access it. When the Windows desktop appears, click Start, Programs, and Windows Explorer. On the back of the floppy drive you will find a red, yellow, and black cable and a flat, gray ribbon cable. What Dos Command Do You Use To Erase A Hard Drive And Make It Bootable?

Click Device Manager. Work on a hard flat surface over a non-carpeted floor. Type hardware troubleshooter in the Search field, then click the arrow to start the search. navigate here warning: The edges of metal panels can cut skin.

After Windows has fully loaded, test the floppy drive. Hdd Controller Failure Beep Codes Your computer might emit a series of beeps during start-up if the monitor cannot display errors or problems. Help Describes the test and may indicate requirements for running the test.

Replace the floppy if the floppy data cable did not resolve your issues.

Option Function Express Test Performs a quick test of devices. No memory modules are detected. Step 5: Reinstalling the drivers for the drive In Windows XP, click Start, right-click My Computer, and select Properties. Floppy Disk Drive Problems The current standard setup is:Drive A : 1.44, 3.5 in.Drive B : None (unless you have two Floppy Drives)Press [ESCAPE] to exit Standard CMOS setup.

I have tried four different floppy drives and two different cables but still get the same result. Once in SETUP you need to check that CMOS is identifying your Floppy Drive and that it is the correct one (i.e., 3.5 in., 1.44MB is the current standard for diskette Recently added New Hardware?If you have such as a tape backup unit, sound card, scanner, network card, etc. http://3cq.org/error-code/what-is-win-error-code-2.php If your computer beeps during start-up: Write down the beep code.

How does HP install software and gather data? Click Standard floppy disk controller. Thanks for any help you can give.Dawn Huber Share Flag This conversation is currently closed to new comments. 10 total posts (Page 1 of 1)   + Follow this Discussion · Thanks for your help! 0Votes Share Flag Collapse - Microsoft's Knowledge Base bulletin: by nepenthe0 · 8 years ago In reply to Floppy drive failed (40) ...

To remove and then reinstall the program: Click the Start button, click Control Panel, and then click Add or Remove Programs. Additional information Unable to read floppy diskette. It worked fine before so I don't understand. Another failure has occurred.

Close the test screen to return to the Main Menu screen. In Windows 98 and Me, right-click the My Computer icon on the desktop, and then select Properties. Let me know and I'll get it corrected as soon as I can. If the problem still exists, install a graphics card that you know works and restart the computer.If the problem persists or the computer has integrated graphics, contact Dell (see "Contacting Dell"

If you wait too long and the operating system logo appears, continue to wait until you see the Microsoft® Windows® desktop. Are these drives new or used.This error generally means that the unit has died.Error code 31: ERROR_GEN_FAILURE - A device attached to the system is not functioning. 0Votes Share Flag Collapse