Home > Error Code > Whirlpool 6th Sense Error Code F06

Whirlpool 6th Sense Error Code F06

Contents

Check pressure switch contacts and connectors Failure of the pressure switch or level sensor can also give rise to this fault code Run test program If failure persists after test and F32 PRESSURE SWITCH FAILURE If there is no electrical supply to the Pressure Switch from the CCU or if the Pressure Switch contacts are worn out, then a Pressure Switch Failure Browse Categories Answer Questions Whirlpool Washing Machine Washing Machines All Unanswered Join Sign In Ask a Question × HomeForumWashing MachinesWhirlpoolGetting faulf code... On this range of Whirlpool washing machines the error can be show as a result of a mains power glitch, usually a power spike. this content

If anyone else sees the same problem try taking other appliances off the outlet, turning off fluorescent lights, etc, and let me know if it goes away. F63 TOTAL STEAMER FAILURE If this Failure is displayed, one or several vital values are out of range. Please advise :) Reply Quote MD Ekramul Haque 1 year 2 months E1 error. Verify inlet valve operation.

Whirlpool Duet Washer Troubleshooting F06

Whirlpool GHW9400... Check wiring between motor control unit and main electronic controller Check all connectors are secure and connections are good Check motor control unit functions Check main control unit F23 Pressure Plug in washer or reconnect power. 4.

had 2 different repair man to fix it and its still doing it Reply Quote c.gray 1 year 9 months whirlpool HDW 1011WG dL then F FLASHING WHAT DOES THIS MEAN F70 CENTRAL CONTROL UNIT HEARTBEAT FAILURE If a Central Control Unit Heartbeat Failure is displayed, no communication is detected from the Central Control Unit to the User Interface. 1. They undergo quite a lot of friction, and after a while wear out. F06 Error Code Whirlpool Dryer After you do this put the machine into a service cycle (see the instructions in the tech sheet found inside the unit or you can borrow mine).

Have a manual for Whirlpool Washing Machines? Whirlpool Duet Washer Error Code F06 E02 The machine will try to detect the reading several times before aborting the program ans shutting down with this error being displayed. Check wire harness connections to the door switch/lock unit and Central Control Unit (CCU). visit Düşüncelerinizi paylaşmak için oturum açın.

In virtually all cases, other then where there is an obvious fault, this will be a use related issue. Whirlpool Carbon Brushes I'm surprised that the motor solved the issue. PUMP DRIVE ERROR The pump driver fails to activate. The drainage pipe was blocked so I simply un-clogged it and made the machine drain and it all seems to be going well.

Whirlpool Duet Washer Error Code F06 E02

Replace heater. click resources F65 STEAMER TIME OUT REACHED Error happens if there is no communication between Central Control Unit (CCU) and steamer electronic board. Whirlpool Duet Washer Troubleshooting F06 For spares, if it isn't glaringly obvious which one is required please contact us and ask and have the 12NC number from the rating plate of the washing machine. Whirlpool Duet Washer Error Code F06 E01 I don't think the wife will like unplugging the washer for a few minutes everytime it throws this code Last edited by Jake; August 13th, 2010 at 08:06 PM.

This relay is fitted on the main electronic controller and it is highly unlikely that there is an issue with the electronic board that controls the drive motor. news Jake Appliance Repair School 1987-1988 Star Appliance Tech. 2 yrs. 1988-1990 Wards Appliance Tech. 11 yrs. 1990-2001 Sears Appliance Tech. 4 yrs. 2001-Oct. 2005 Jake's Appliance Repair Nov. 2005-present Look-Up & Replace the pump. NOTE: During first power up of new CCU and UI combination, a bootphase (uploading parameters) will be performed. Whirlpool Duet Error Code E02

Search All Our Sites for Awesome Appliance Repair Help! If the motor seems to run fine that way, put the belt back on and run it again. Unplug washer or disconnect power for two minutes. have a peek at these guys Thanks in advance Reply Quote Gonçalo Ribeiro 1 year Hi, I have the error messagem: E1-F8, and the machine didn't turned out the water, there is water in the machine.

French Door Bottom-Freezer Refrigerator with EasyFill Internal Water Dispenser Range 30" Freestanding Electric Range with a 5.4 Cu. Whirlpool Dishwasher F6 Error Code The control must realize that the trip was due to an overfill condition instead of a suds lock condition in order for "FL" to be displayed. LF Long fill If the water fill time exceeds ten minutes, the water valves are turned off and "LF" is flashed.

Verify wire harness connections to inlet valves, pressure switch, flow meter, and Central Control Unit (CCU). 4.

Motor solved the issue. $25 for the used motor on eBay. Flashing display time Open lid If the lid opens while the unit is in running mode, time remaining will flash in the display. DPLrepara 83.714 görüntüleme 2:34 Daha fazla öneri yükleniyor... F06 Error Code Hotpoint Ft.

I turned power offf and on then got the door to open. I'd sure like to find it while it's still covered by the extended warrantee. D. check my blog What's New?

the fridge is still working. Tech said we would be waiting for 2-4 weeks to get the part. Plug in washer or reconnect power 7. F08 Open circuit error detected on heating circuit The main control unit in the washing machine has detected that there is an open circuit somewhere in the heating circuit.

Replace heater. The washer does not flash "PF" when it is first plugged in. Was this answer helpful?