Home > Error Code > Whirlpool Appliances Error Codes

Whirlpool Appliances Error Codes

Contents

If error continues, disconnect power and replace control. Refer to the Water Temperature Sensor section. Note: The door lock/switch assembly can be manually unlocked. Recall Alerts Careers PartSelect Canada Free Repair Help Appliance Repair Instant Repairman Dishwasher Dryer Microwave Range / Stove / Oven Refrigerator Washing Machine Helpful Resources PartSelect Community Twitter Facebook Page YouTube this content

F65 STEAMER TIME OUT REACHED Error happens if there is no communication between Central Control Unit (CCU) and steamer electronic board. Other F# E# code Unplug the washer or disconnect the power for one minute and reconnect it again. OR Press STOP/CANCEL to clear the display and completely cancel the cycle. The drive motor must be hooked up properly or a "CE" error will occur. • Drive motor thermal protector has opened. • Motor controller is not powered or fuse has opened. http://www.appliancepartspros.com/repair-help/whirlpool-fault-codes.html

Whirlpool Washing Machine Error Codes E1

Reach up along the inside of the front panel and locate the bottom of the door latch assembly. 4. If resistance is 0 Ω or infi nite value, replace NTC. 4. Please remember to support our site by buying Whirlpool washing machine spares from our spare part storeand, if you decide that you need a washing machine engineer please support the local Disconnect power for at least 30 seconds. 2.

F7 - Function Key Stuck - Replace control board (clock). Plug in washer or reconnect power. 5. Check wire harness connections to the drain pump, pressure switch, water inlet value, and Central Control Unit (CCU). 4. Whirlpool Oven Error Codes E2 F3 Unplug washer or disconnect power for two minutes.

Press 'Stop/Cancel' to clear display. This should clear the unit of the excess detergent. 1. Measure latch switch (unlatch = switch open, CAUTION - oven light contacts are closed). http://www.partselect.com/JustForFun/Whirlpool-Appliance-Fault-Codes.aspx Check keypad connector for firm connection (keypad connects to control board). 2.

codes. Whirlpool Range Error Code F9e0 Overloading the unit may also cause this problem. Check wiring between motor control unit and main electronic controller Check all connectors are secure and connections are good Check motor control unit functions Check main control unit F23 Pressure On this range of Whirlpool washing machines the error can be show as a result of a mains power glitch, usually a power spike.

Whirlpool Top Load Washing Machine Error Codes

Potential Causes • Check Wire Harness connections to the MCU, the motor, and Central Control Unit (CCU) • Check Drive belt • Check MCU • Check Motor • Check Wire Harness http://www.how-to-repair.com/help/how-to-enter-test-mode-on-whirlpool-awod-awd-series-repair-faults-test-errors/ If door not latched: Disconnect power from unit. Whirlpool Washing Machine Error Codes E1 Check pressure switch contacts and connectors Failure of the pressure switch or level sensor can also give rise to this fault code Run test program If failure persists after test and Whirlpool 6th Sense Washing Machine Error Codes If there is no water supply or a restricted supply from the likes of a low mains water pressure then this error code will be shown.

F13 Dispenser circuit error If the dispenser motor is not able to be driven to it’s proper position. news Category Science & Technology License Standard YouTube License Show more Show less Loading... In the case Whirlpool dishwasher not draining, refer for technical help to dishwasher repair shop Whirlpool. Check that the serial harness at the MCU is not mounted upside down. Whirlpool Washer Error Codes F21

Check for stuck lock switch. Measure door switch (door open = switch open small low voltage terminals). F1 - E1 EEPROM checksum error F1 - E2 UL A/D error(s) F1 - E4 Model ID error F1 - E5 Calibration shifted F1 - E6 Latch signal mismatch error F1 have a peek at these guys Unplug washer or disconnect power. 2.

Potential Causes • Check wire harness connections between the Drive Motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU) • Check the MCU Whirlpool Washing Machine Error Code Pe Random Repair 66,386 views 9:38 Loading more suggestions... Press STOP/CANCEL to clear the display.

Refrigerator 25 Cu.

FdL Door lock error A Door Lock Error occurs if the door cannot be locked.

Do i need to get someone in or can it be fixed myself? The motor control unit has detected that the voltage supplied to it is less than 170V AC and this is not a defect of the component itself but of the mains Look for welded relay contacts on bake or broil relays. Whirlpool Split Ac Error Codes Check water heating element for continuity Check water heater for earth leakage check heater resistance Check all wiring and connectors to the heater and from there to the main controller Check

Exchange the complete valve block if the steamer valve has not a resistance of approx. 812 Ω between both contacts. 6. F42 MOTOR CONTROL UNIT FAILURE - REPETITIVE UNDERVOLTAGE The Motor Control Unit continuously checks for voltage. How to Enter Test Mode Sequence To enter the diagnostic/test mode sequence, you need to turn the dial to the DRAIN position, which is at eleven o´clock; then you must press check my blog F06 Drive motor tachometer error The control is unable to properly detect motor speed and the machine will shut down.

When you power on the washing machine and voltage is supplied to the motor control unit it performs a self test sequence automatically. Check the wire harness connections to the Motor Control Unit, Central Control Unit, and Interference Filter. 3.