Home > Error Code > Whirlpool Dryer Error Code E1

Whirlpool Dryer Error Code E1

Contents

Note: This error may signify a bad pump, an extra heavy load, excessive detergent, or excessive suds. Electric Dryer Troubleshooting Dryer Takes Too Long to Dry Clothes? Press and hold any key to clear the error code and F2 code should appear. Shop Parts Repair Help SEARCH Return to previous page Whirlpool Dryer Displaying Fault Code E1, E2 7MGGW9868KQ1 Thermistor Failure The manufacturer has assigned this error or fault code to indicate a this content

Ask Your Own Appliance Question Expert: I.can replied7 years ago. Press and HOLD start to continue the cycle, or press 'Stop/Cancel' to clear display and cancel cycle. If damage is found, replace appropriate part. F7-E1 - Common Switch Wire Is Defective - This error occurs when common wire to latch switch and door switch is shorted. http://www.repairclinic.com/RepairHelp/How-To-Fix-A-Dryer/376-5-619505-/Whirlpool-E1-E2-Thermistor-Failure

Whirlpool Duet Washer E1 Error Code

F7 - Function Key Stuck - Replace control board (clock). Check the inlet valve and pressure switch for proper shut off and operation. or exceeds 250 degrees F. Click here for more details.

Check for stuck lock switch. SL - Suds Lock - This error will occur if the unit detects suds but is unable to clean them out. Replace failed component. E1 Error Washing Machine All F5-E Codes - Door Switch Defect - This occurs when the door switches do not match.

Loading... The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd. Make sure the drain pump is free from debris or foreign objects and then reconnect power and plug unit in.

See inside of your appliance - diagrams and part photos for virtually every model.

Check the door switch/lock for any debris or foreign objects. Whirlpool Top Load Washing Machine Error Codes The Discuss-o-Mat has stopped, buzzer is sounding!!! Also check all components for defects. See Details Whirlpool WTW7000DW 4.8 cu.

Whirlpool Duet Thermistor

Loading... http://applianceguru.com/forum1/78.html When the thermistor circuit is open (>50K ohms), the error code E1 flashes in the display. Whirlpool Duet Washer E1 Error Code Turn off hot and cold water to faucets and unplug the unit before proceeding. E1 Error Code Kenmore Dryer Allow at least a minute after power has been restored and if error code reappears, replace control board (clock).

F06 - Drive Motor Tachometer Error (Unable to Detect Motor Speed) - Disconnect power and unplug unit. news Find out more » Total: $17.20 Add to Cart Install Help Watch this helpful video to determine how to install your part. Close the dryer door. 4. Working... Maytag Dryer Error Code E1

How can I remedy the situation? Disconnect power and unplug unit to check wire harness connections to the Central Control Unit (CCU) and the door switch/lock unit. How to fix the thermostat and heater element - Duration: 8:34. have a peek at these guys If F8E1 or LF (too long to fill) appears in display, the washer is taking too long to fill.

CE - Communication Error - Disconnect power and unplug unit. Whirlpool Dishwasher E1 Error Code F11 - Serial Communication Error Between MCU and CCU - Disconnect power and unplug unit. Please make sure both inlet hoses are connected and both hot and cold water supplies areturned on.

I have to go to my shop now and i'll pick this up when I get there..

Press and HOLD start to continue the cycle, or press off/pause to clear display. Check the thermistor with an Ohm meter, if it reads >50k Ohms (E1) or less than 500 Ohms (E2) it is defective. Allow at least a minute after power has been restored and if error code reappears, replace control board (clock). E1 Error Baseball Skip navigation UploadSign inSearch Loading...

Electric Dryer Troubleshooting Dryer Takes Too Long to Dry Clothes? Brand WHR Media faulttree Topic assistance Tags This page has no tags. © Copyright 2016 Whirlpool Home Appliances Powered by MindTouch                 A defective thermistor is not responsible for a dryer not heating. $17.20 Quantity: In Stock › Suggested tools Multi Screwdriver RepairClinic Item #3527472 $14.95 Same Day Shipping Order by 8:00 PM http://3cq.org/error-code/whirlpool-duet-dryer-e1-error-code.php Live Chat 1-800-269-2609| En Español| Available 7 days a week RepairClinic.com Logo Fast Shipping My Orders Login Order History My Model Numbers Cart(0) What is a model number, and where

Check the drive system for any worn or failed components and reconnect power and plug unit in. What about a Whirlpool washer that doesn't always disperse the fabric softener. This error code is indicating that the exhaust air temperature is either below 18 degrees Fahrenheit or above 250 degrees Fahrenheit. Again our apologies for the inconvenience.

Unplug the unit and disconnect the power to check all wire harness connections to the inlet valve, pressure switch, drain pump, flow meter, and Central Control Unit (CCU). If error continues, disconnect power and replace control.