Home > Error Code > Whirlpool Duet E1 Error Code

Whirlpool Duet E1 Error Code

Contents

Happy Holidays. The error code F9 E1 will be displayed on most newer Maytag washers and Whirlpool washers.  If this error code has popped up on your washer then this article is for If a potential suds lock is detected, the control tries up to 3 times to clean out the unit with a mini-cycle. "SL" is displayed if suds are detected but the Thanks Reply Dotsy says: June 13, 2015 at 2:07 am Worked like a charm! have a peek at these guys

Instantaneous current trip occurs if there is a spike of 26 Amps instantly at the motor windings. OR Press STOP/CANCEL to clear the display and completely cancel the cycle. Happy to help. Unplug washer or disconnect power. 2.

Whirlpool Washing Machine Error Code E1

F7 Function key stuck on ERC Replace control board (also called ERC or clock). F8E4 Error - Flow meter fault. Lastly F9 faults are related to the washer's ability to drain. We are now having to do this almost every other load now.

Check the MCU by looking for operations of the drive motor. 7. Again, thanks for everything! found a big red wool sock, a tooney, a quarter, some screws, and some bobby pins! Whirlpool F9e1 Check wire harness connections to the door switch/lock unit and Central Control Unit (CCU). 4.

I also had F1 E9 error. Check for continuity of the User Interface harness. 2. Need A Tech Sheet or User Manual For A Whirlpool Duet Washer WFW70HEBW? http://www.techanswerslive.com/appliances/whirlpool-duet-washer-error-code-f3-e1/17/ Good work checking everything between out.

Patricia Reply Preston Snyder says: March 17, 2016 at 1:28 am This took care of our problem tonight! E1 Error Code Kenmore Dryer Does the dryer need to be taken out so you can get to the sides? codes. Sud SUDS LOCK (OVERDOSE OF DETERGENT DETECTED DURING THE WASH CYCLE) If suds are detected continuously by the pressure switch during the drain or spin phases, the washer will fill 4

Whirlpool Duet Thermistor

F32 PRESSURE SWITCH FAILURE If there is no electrical supply to the Pressure Switch from the CCU or if the Pressure Switch contacts are worn out, then a Pressure Switch Failure http://www.appliancepartspros.com/repair-help/whirlpool-fault-codes.html Matt Reply Doris Oder says: May 2, 2015 at 11:24 pm My Maytag 2000 series is giving me the E1 F9 error code. Whirlpool Washing Machine Error Code E1 You'll need a multimeter to check for power. Whirlpool Duet Washer Error Code E1 F8 See Whirlpoool Duet Washer Water Pressure Switch Test
Chat Live With a Whirlpool Duet Washer Technician Now!

codes. http://3cq.org/error-code/whirlpool-duet-error-code-f27.php Reply Matthew says: August 28, 2015 at 6:21 pm Hi, you're most welcome. Reply Matthew says: May 2, 2015 at 4:54 pm Bill, You're most welcome. Great post!! Maytag Washer Error Code E1 F9

Plug in washer or reconnect power. 4. Replace sensor if found defective. Check that the tab on the washer's door that inserts into the door lock is not broken, that it's properly aligned with the door lock hole, and that there is nothing check my blog Reply Carie says: November 16, 2015 at 3:41 am Thanks so much for your excellent directions and help!

It will try to lock it 6 times before displaying the error. Maytag Dryer Error Code E1 Gas Dryer Troubleshooting Most Frequent Causes for E1, E2 - Thermistor Failure See All Dryer Parts for model 7MGGW9868KQ1 Cause 1 Thermistor Parts Thermistor for your Whirlpool Dryer RepairClinic Item #1181075 My old washer had the access panel as described in your article and easy to undo and clear debris.

Check plumbing for correct drain hose installation.

The control should not allow the unit to run in this condition. check that the washer's water valves are closing all the way and water is not filling into the tub when it shouldn't be. I read some things online and a few places said that it could be the placement and position of the exhaust tube, currently I havent done poop with it, everything takes Maytag 2000 Series Washer Error Codes 5d The pump is cycled in drain mode for 30 seconds on, 30 seconds off until the overfill switch resets or power is discontinued to the unit.

I'm glad you found the information useful. Reply Matthew says: May 25, 2015 at 7:15 pm Denise, You're most welcome. F24 WATER TEMPERATURE SENSOR ERROR If the water temperature sensor (NTC) value is out of range (23°F to 217°F[-5°C to 103°C]) during the water-heating step of the WASH cycle. http://3cq.org/error-code/whirlpool-duet-02-f-error-code.php With this failure, power to the motor controller cannot be turned off by the machine controller.

Press PAUSE/CANCEL twice to clear the display. What other things might we maintain to avoid nuisance codes? Matt Reply Theresa says: August 30, 2015 at 4:48 am Thank you so much for posting this! Help Matthew!!!

Loading... Check wire harness connections to the User Interface and the Central Control Unit. 3. Anybody know what is causing this? I’m still getting F9E1 errors.

Verify inlet valve operation. Reply Geoff says: February 6, 2016 at 11:27 pm Hi and thanks for the awesome advice. This may signify problems with the drive motor, thermal protector or motor controller. Good luck.

If F8E1 or LF (too long to fill) appears in display, the washer is taking too long to fill. Now you can clean out the drain filter. Reply Matthew says: May 3, 2015 at 3:52 pm Doris, what have you done so far? Check the water temperature sensor and connection to it.

F02 Long Drain If the drain time exceeds 8 minutes, the water valves are turned off and F02 is flashed. Matt Reply Tommy says: May 25, 2015 at 11:41 pm Great info… I cleaned out the basket and checked the hose but I still have the same code halfway through the