Home > Error Code > Whirlpool Duet Gas Dryer E1 Error

Whirlpool Duet Gas Dryer E1 Error

Contents

Verify wire harness connections to inlet valves, pressure switch, drain pump and Central Control Unit (CCU). 5. Thanks again. Unplug washer or disconnect power. 3. Credentials confirmed by a Fortune 500 verification firm. http://3cq.org/error-code/whirlpool-duet-dryer-e1-error-code.php

If there is an error reading this data it will cause this error. Replace CCU board. ft. Thank you for supporting our free repair help forum. #7 (permalink) 07-20-2010, 12:39 PM Thomas Smythe Junior Member Join Date: Jul 2010 Posts: 2 Appliance Parts Pros are

What Does E1 Mean On Whirlpool Duet Dryer

Unplug washer or disconnect power. 3. Cause 2 Air Flow Problem The manufacturer has assigned this error or fault code to indicate a possible problem with are flow or the heating system in the dryer. Exchange Steamer if it is totally blocked. Replace sensor if found defective.

AppliancePartsPros.com is the registered trademark of AppliancePartsPros.com, Inc. The failure will be reset after running the Diagnostic Test Program is run. 1. How to fix the thermostat and heater element - Duración: 8:34. Maytag Dryer Error Code E1 S.E., Cleveland, TN 37311 Legal Notice|Privacy Notice©1999 - 2012Appliance Parts Pros.com.

Check that NTC resistance of the Steamer is in range between 170 kΩ and 300 Ω, refer to Temperature Sensor table.If resistance is 0 Ω or infi nite value, replace NTC. Whirlpool Duet Dryer Thermistor Press STOP/CANCEL to clear the display. Potential Causes • If too much detergent was used, run the unit through a Rinse/ Spin cycle then a Normal cycle without adding any detergent. Remove them and the panel comes right off.

F1 Board failure Replace control board (also called ERC or clock). E1 Error Washing Machine Door switch/lock unit failure. 1. Located on the bottom of the door latch assembly is a tear-drop shaped tab. 5. If failure occurs during high-speed spin the door unlocks after 3 minutes. 1.

Whirlpool Duet Dryer Thermistor

F29 DOOR UNLOCK ERROR If the door unlock has failed 6 times. See inside of your appliance - diagrams and part photos for virtually every model. What Does E1 Mean On Whirlpool Duet Dryer Unplug washer or disconnect power for two minutes. Whirlpool Duet Washer Error Code E1 My research shows the part number Part number: AP3919451 thermistor is not included in the kit Part number: AP3094244 .

This may signify problems with the drive motor, thermal protector or motor controller. More about the author Exchange steamer electronic board if valve is OK. Check wire harness connections to the drain pump, pressure switch, water inlet value, and Central Control Unit (CCU). 4. If there is water in the unit: Verify that the pressure switch hose is in good condition and properly connected to tub and pressure switch. 1. E1 Error Code Kenmore Dryer

Remember: Oven control (ERC) measures resistance of sensor circuit, not actual oven temperature. F20 NO WATER DETECTED ENTERING MACHINE OR PRESSURE SWITCH TRIP NOT DETECTED. If a failure occurs during high-speed spin the door will be unlocked after 3 minutes. check my blog Buy appliance parts from us.

Jim Post# 440495 , Reply# 1   6/8/2010 at 21:56 (2,337 days old) by nmassman44 (Boston North Shore Massachusetts)     Checkrate/Likes       Whirlpool Top Load Washing Machine Error Codes Check the thermistor with an Ohm meter, if it reads >50k Ohms (E1) or less than 500 Ohms (E2) it is defective. FL Flood condition "FL" flashes if any overfill condition occurs.

Check pins 1 and 5 of P16 of the machine controller and pins 1 and 2 of P1 of the motor controller.

TEMP RESISTANCE TEMP RESISTANCE C (F) (K Ω ) C (F) (K Ω ) 10 (50) 19.9 43 (110) 4.7 16 (60) 15.3 49 (120) 3.7 21 (70) 11.9 54 (130) CE Communications error If there is any breakdown in communication between the machine controller and the motor controller, "CE" flashes and the unit beeps once. thanks again Back To Top Posted: Mon Sep 12th, 2005 04:54 am 13th Post Samurai Appliance Repair Man Fermented Grand Master of Appliantology Joined:Mon Mar 21st, 2005 Location:Otterville, Whirlpool Dishwasher E1 Error Code The correct exhaust tem- peratures for the various settings are shown in the following chart. 9.

If you measure normal resistance (10K ohms) at the thermistor, then you will need to repair the wiring connection between the control board and the thermistor. If you measure the proper Website related questions? any ideas as to what the problem may be? news With an overfill condition, the beeper repeats a warning every 10 seconds with no time out.

Check all hoses for possible leaks. 5. The thermistor attaches to the control board on the P2 connector (red/white and black wires on pins 5 and 6). F63 TOTAL STEAMER FAILURE If this Failure is displayed, one or several vital values are out of range. Check wire harness connections to the MCU, the motor, and Central Control Unit (CCU). 4.

If there is water in the unit: Verify drain pump operation. Rate, comment, and subscribe. LinkBack Thread Tools Search this Thread Display Modes #1 (permalink) 02-22-2008, 10:56 AM toneal Junior Member Join Date: Feb 2008 Posts: 1 Whirlpool Senseon gives E1 error code The clothes never finish drying and its really starting to be a pain.

Verify CCU operation by running a Diagnostic Test or any cycle. 6. Repeat steps A and B for door switch. 3.