Home > Error Code > Whirlpool Duet Sport Washer Error Code F 26

Whirlpool Duet Sport Washer Error Code F 26

Contents

We were getting a F/22 error code, but since we replaced the latch we are now getting a F/26 code. Unplug washer or disconnect power. 2. Replace the Motor Control Unit. Sud SUDS LOCK (OVERDOSE OF DETERGENT DETECTED DURING THE WASH CYCLE) If suds are detected continuously by the pressure switch during the drain or spin phases, the washer will fill 4 have a peek at these guys

Check the Water Temperature Sensor, Heating Element and Element Relay Check connections to the Sensor, Heating Element and Relay F/06 Drive Motor Tachometer Error The control is unable to properly detect Very much appreciated. Check the MCU by looking for operations of the drive motor. 7. If a failure occurs during high-speed spin, the door will be unlocked after 3 minutes.

Whirlpool Duet F26 Error

Check wire harness connections to the drain pump, pressure switch, and Central Control Unit (CCU). 4. Check Wire Harness connectors to the MCU, and Central Control Unit (CCU) Check the Drive system for any worn or failed components Check MCU Check Motor F/11 Serial Communication Error Communication Posted on Jun 18, 2013 Helpful 1 Not Helpful Comment Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images Anonymous Re: F 26 Code that I have to unplug it to get control of the functions again.

Thanks/Mike Nov 03, 2007 | Whirlpool Duet GHW9150P Front Load Washer 1 Answer Whirlpool duet ht will not agitate or spin Front load washers don't "agitate". Mismatch of User Interface and CCU or corrupted EEPROM. 1. It's Sat on a holiday weekend so getting someone to come and fix this will be a long wait... Whirlpool Duet Sport F26 Gotta love the internet!Thank you so much!

Plug in washer or reconnect power. Whirlpool Duet Dryer F26 Error Code The failure will be reset after running the Diagnostic Test Program. 1. NOTE: Detects by weight.

Plug in washer or reconnect power.

Door switch/lock unit failure. 1. Whirlpool Washing Machine Error Codes Parts Search Fixitnow Site Search Search for: Appliance Repair Training and Support Proudly powered by WordPress Admin Login Learn appliance repair online from experts at the Master Samurai Tech Academy! Check all hoses for possible leaks. 6. Verify CCU operation by running a Diagnostic Test or any cycle.  

Whirlpool Duet Dryer F26 Error Code

May 17, 2010 | Whirlpool Duet GHW9150P Front Load Washer 1 Answer I have a whirlpool duet ht front load. Coil/Stator Assembly will be defective preventing the drive to operate.You should go for a replacement of that assembly. Whirlpool Duet F26 Error Check the drain hose and make sure it is not plugged or inked. Kenmore Washer Error Code F 26 Check wire harness connections to the drain pump, pressure switch, water inlet value, and Central Control Unit (CCU). 4.

I hope this helps. More about the author Check drain pump. 7. Check the pressure switch. 8. Corporal: An expert that hasĀ over 10 points. F26 Error Code Whirlpool Washer

Loading...Oops :Please try again. If the washer works, you know it was the door switch. F29 Door Unlock Error A Door Unlock Error occurs if the door cannot be unlocked. check my blog How to Use a Multimeter F11 MCU (Duet Motor Control Unit) Error The motor control board is having some problems...

Unplug washer or disconnect power. 3. Whirlpool 6th Sense Washing Machine Error Codes Failure Code LED Status Duet Sport LED Status Duet Sport HT F01 Add a Garment Add a Garment F11 Add a Garment, Wash, Spin Add a Garment, Soak/Prewash, Rinse F20 Rinse, F24 WATER TEMPERATURE SENSOR ERROR If the water temperature sensor (NTC) value is out of range (23°F to 217°F[-5°C to 103°C]) during the water-heating step of the WASH cycle.

The resistance of both door coils (between pin 1 and 3) should be approximately 320 ohms.You can remove the lower kick panel and open the cabinet up and see if you

All rights reserved. NOTE: If the error remains on the display, call for service. NOTE: During first power up of new CCU and UI combination, a bootphase (uploading parameters) will be performed. Verify pressure switch operation. 7.

Language: English (UK) Content location: United Kingdom Restricted Mode: Off History Help Loading... First press the pause/cancel button to clear the error display. F42 MOTOR CONTROL UNIT FAILURE - REPETITIVE UNDERVOLTAGE The Motor Control Unit continuously checks for voltage. http://3cq.org/error-code/whirlpool-washer-duet-sport-error-code-f28.php Rave Reviews "I thought it was the best online shopping experience that I have ever had when it comes to parts." Eric H.

ft. If it doesn't work then you almost certainly have a clog in your Duet washer's drain system and the pump may be fine. Check for proper installation, verify the unit is not located near a source of heat and has proper ventilation. 2. Check for plugged or kinked inlet hoses or plugged screens in the inlet valves 3.

The failure will be reset after running the Diagnostic Test Program. 1. Check the inlet valve for proper shut off. 7. See Details Whirlpool WTW5000DW 4.3 cu. Push the door and check if it completely closed.

Verify CCU operation by running a Diagnostic Test or any cycle. 3. Verify CCU operation by running a Diagnostic Test or any cycle. Check/clean drain pump filter of foreign objects. 5. Remove the switch by disconnecting the wire harness and the rubber tube connected to it and gently rotate it 90 degrees CCW and you should be able to pull it out

Once the connector is removed, it should reset the control. Pressure Switch Hose is in good condition and properly connected to Tub and Pressure switch Verify there is not a siphon problem Verify wire harness connections to:Inlet Valves, Pressure Switch, Drain