Home > Error Code > Whirlpool Duet Washer Error Code F 06

Whirlpool Duet Washer Error Code F 06

Contents

how-2-repair.com 309 viewsNew 20:18 Top 5 Reasons Front-Load Washer Won’t Spin? — Washing Machine Troubleshooting - Duration: 2:04. Rating is available when the video has been rented. No F-06 codes, no problems (other than having to dump all that water). Still think it's an MCU or a weak motor. have a peek at these guys

I was always able to get it working again, just not in a timely manner. Here's the excerpt from the Whirlpool Duet Service Manual on this: Drive Motor Tachometer Error The control is unable to properly detect motor speed and the machine will shut down. Leave a Reply Click here to cancel reply. Page 1 of 3 123 Last Jump to page: Results 1 to 10 of 23 Thread: Whirlpool Duet F06 error code Thread Tools Show Printable Version Search Thread Advanced Search

Whirlpool Duet Washer Error Code F06 E02

Across my 4 and 5 terminals it is at 185 OHM's. Cabrio® Top ... Show more Language: English Content location: United States Restricted Mode: Off History Help Loading... Sign in to add this video to a playlist.

The content in this area cannot be displayed because your browser has JavaScript disabled (or does not support it, not common). Please try again later. The connectors are numbered 1 to 3 (L to R). Whirlpool F06 What Your Appliance Error Code Really Means.

Pushing the pins inside tight will make sure the contacts are working. Whirlpool Duet Washer Error Code F06 E01 However, before the code comes up, the door locks and it fills with water. Sign in to make your opinion count. navigate to these guys I did notice that my drum will "jerk" at the beginning of the cycle but will not spin.

the plug has a few pins inside. Whirlpool Duet F6 Error Code here is more info from here Check the MCU. Please click here if you are not redirected within a few seconds. Seems there should be a better fix...

Whirlpool Duet Washer Error Code F06 E01

I will also check the the connections on the MCU. http://www.shopyourway.com/questions/1071098 Loading... Whirlpool Duet Washer Error Code F06 E02 C.L.S. F06 Error Code Kenmore Elite Washer Yes No Voted Undo Score 0 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz?

The author of this site has no liability for errors, omissions, or any defects whatsoever in the information or instructions, or for any damage or injury resulting from the utilization of More about the author Suppose the motor turns easily and freely by hand but won't run either with or without the belt. Cancel Marty Rep: 1 Posted: 10/20/2013 Options Permalink History Based on some troubleshooting, I have begun to suspect the intermittent F06 error on my Whirlpool Duet GHW9400 is due to noisy If you have your model number I am including a link that you may input your model number and see a parts breakdown, please click here; Sears Parts Direct If Whirlpool Duet Error Code E02

December 1st, 2010,01:47 PM #8 3fordasho View Profile View Forum Posts Premium Member Join Date Feb 2006 Location Minnesota Posts 8 Originally Posted by sandyds how do you reset it? Anything else I can check? Can you please elaborate on what you mean by "checking" the drive motor, the MCU and the wire harness. check my blog So if you get the error intermittently try cleaning up the power and post whether it's fixed.

Good luck. F06 Error Code Whirlpool Dryer Sign in to add this to Watch Later Add to Loading playlists... Top-Load ...

After checking all connections per the service manual, all OK, the machine now stops with the estimated time remaining flashing.

Keeping fingers crossed. Pins 1 to 2 should read 120VAC with the door in the locked position. Powered by vBulletin Version 3.6.4Copyright ©2000 - 2016, Jelsoft Enterprises Ltd. Whirlpool Carbon Brushes Yes No Voted Undo Score 1 Cancel Comments: Old Turkey - yes I did download the service manual.

I ran the diagnostic test and during the step when it is supposed to check the drum spinning nothing happens. The content in this area cannot be displayed because your browser has JavaScript disabled (or does not support it, not common). how-2-repair.com 39,071 views 8:55 How to Diagnose Washing Machine Control and Program Problems - Duration: 9:08. news Shop Game of Thrones costumes and accessories!

All the connector pins are numbered R to L. Bad MCU? by bill billy Earned 8 community points in Click'>Whirlpool July 15th Comment 0 votes Model numberGHW9300PW4 by Kenneth A Hayes Earned 8 community points in Click'>Whirlpool 26 days ago Comment 0 Skip navigation UploadSign inSearch Loading...

Was this answer helpful? Sign in 219 11 Don't like this video? Here's the MCU(motor control unit) for your model: Motor Control Board 8182706 Order now for same day shipping. 365 day return policy. Its likely a bad motor, as other members have reported that a new motor fixed it permanently.

All readings should be approximately 6 ohms.. RepairClinic.com Jake Appliance Repair School 1987-1988 Star Appliance Tech. 2 yrs. 1988-1990 Wards Appliance Tech. 11 yrs. 1990-2001 Sears Appliance Tech. 4 yrs. 2001-Oct. 2005 Jake's Appliance Repair Nov. 2005-present Look-Up Remove the connector plug and check across pins 1 to 2, 2 to 3, and 1 to 3. if I press the pause/cancel button while when the timer is not flashing, the machine drains and turns off.

It occurs mostly during a spin cycle and clothes remain wet. I don't think the wife will like unplugging the washer for a few minutes everytime it throws this code Last edited by Jake; August 13th, 2010 at 08:06 PM. Get Your Ugly Christmas Sweater here. Jake Appliance Repair School 1987-1988 Star Appliance Tech. 2 yrs. 1988-1990 Wards Appliance Tech. 11 yrs. 1990-2001 Sears Appliance Tech. 4 yrs. 2001-Oct. 2005 Jake's Appliance Repair Nov. 2005-present Look-Up &

Have checked the motor, ohm readings OK, rotated the basket, no binding, reseated connectors on the MCU, and run the overview test program, test completed succesfully every time. This means the control is unable to properly detect motor speed and the machine will shut down. Something about they can't just order the part anymore, must come from extended warrantee provider.