Home > Error Code > Whirlpool Duet Washer Error Code F27

Whirlpool Duet Washer Error Code F27

Contents

Check wire harness connections to the drain pump, pressure switch, water inlet value, and Central Control Unit (CCU). 4. Some models do not have the display to show the failure codes. Check the drain hose and make sure it is not plugged or kinked. 2. If a failure occurs during high-speed spin, the door will be unlocked after 3 minutes. have a peek at these guys

Check for drain pump failure.6. Check the drain pump filter for foreign objects. Unplug washer or disconnect power. 3. You may have a loose or dirty connection somewhere. http://www.fixya.com/support/r1484133-f27_error_code_whirlpool_duet_kenmore

Kenmore F27 Error

Unplug washer or disconnect power. 2. F22 DOOR LOCK ERROR After 6 failed attempts to lock the door. F11 MOTOR CONTROL UNIT ERROR The Motor Control Unit has internal failure; repeating under or over voltage, or over current conditions. PUMP DRIVE ERROR The pump driver fails to activate.

F42 MOTOR CONTROL UNIT FAILURE - REPETITIVE UNDERVOLTAGE The Motor Control Unit continuously checks for voltage. Unplug washer or disconnect power. 3. Turn off hot and cold water faucets and unplug the unit beforeservicing. 1. Note: The door lock/switch assembly can be manually unlocked.

See Details Whirlpool WFW90HEFC 4.5 cu. Perform Service Cycle to pair the UI and CCU SW. 2. Check the drain pump filter for foreign objects. 5. Potential Causes • Door lock is broken. • Check door lock switch for foreign objects • Check wire harness connections to the door lock switch and the main control board at

Mismatch of User Interface and CCU or corrupted EEPROM. 1. Unplug your machine anytime you work on it. Exchange the complete valve block if the steamer valve has not a resistance of approx. 812 Ω between both contacts. 6. Some models incorporate keypad in to control board as one unit.

Whirlpool 6th Sense Washing Machine Error Codes

Very good information by the way. https://www.ifixit.com/Answers/View/197890/What+does+the+f27+code+mean Check the heater for resistance... Kenmore F27 Error If the above does not correct the problem, go to step 7. 7. Whirlpool Front Load Washer Error Codes Is it double or triple concentrated?

F3 Oven temperature sensor (RTD) open Replace Oven temperature sensor (RTD) F4 Oven temperature sensor (RTD) shorted Replace Oven temperature sensor (RTD) F5 Board failure Replace control board (also called ERC More about the author Press PAUSE/CANCEL twice to clear the display. F1 Board failure Replace control board (also called ERC or clock). Mend it How can I repair a file error? Whirlpool Washer

This is the hose that attaches to the bottom of the tub and runs to the inlet side of the drain pump. Check that the serial harness at the MCU is not mounted upside down. If there is water in the unit: Verify that the pressure switch hose is in good condition and properly connected to tub and pressure switch. 1. check my blog Replace CCU board.

Yes No Voted Undo Score 0 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? Search Fixya Press enter to search. The Whirlpool Duet front loading washing machine has a diagnostic test mode that can be used to help troubleshoot your washing machine's problem.

NOTE: After 4 minutes the “Sud” error will be displayed, then 4 minutes later the F02 error code will be displayed.

Check the water temperature sensor and connection to it. 3. F2 - E0 Shorted keypad (also called touch pad) 1. Is there a way to remove the drain motor and make sure it is clean? Model # wfw8300sw00. Check the drain hose and make sure it is not plugged or kinked. 2.

This section of the Duet repair guide shows possible error codes, what they may mean, and what to do next! If you remove any connectors, make sure you write down where they go. Cancel Add your answer Tara Barnes will be eternally grateful. news If "Sud" is displayed a potential suds lock is detected.

Opening the lid will allow you to view and redistribute the load. you have checked the drain pump catch correct? Replace User Interface. F07 Motor control unit error The Central Control Unit has detected a short in the motor control unit.

A power glitch may cause this error. normally this is due to too much soap or non HE detergent being used. Press STOP/CANCEL to clear the display. If the error code reappears, proceed to step 2. 2.

Check door switch/lock unit. 3. by Manage My Life August 10th, 2010 Comment 0 votes Didn't find what you are looking for? Replace User Interface if drum is rotating. 4. Check all hoses for possible leaks. 6.

F11 MOTOR CONTROL UNIT ERROR The Motor Control Unit has internal failure; repeating under or over voltage, or over current conditions. Run the water from the faucets for a few minutes. Verify there is not a siphon problem. 2. F29 DOOR UNLOCK ERROR If the door unlock has failed 6 times.

Electronic Board and the valve for steam fill. 4. NOTE: Detects by weight. Verify CCU operation by running a Diagnostic Test or any cycle. Sign in to make your opinion count.

PUMP DRIVE ERROR The pump driver fails to activate.