Home > Error Code > Whirlpool E1 Error Code

Whirlpool E1 Error Code

Contents

Verify pressure switch operation. 7. Check wires and connectors from control to door switch, then from door switch to control. Replace motor controller. Unplug washer or disconnect power. 3. have a peek at these guys

It should be approx. 115 Ω. 4. ginsboy2003 88,065 views 38:35 Dryer Troubleshooting - Not Drying or Taking a Long Time to Dry - Duration: 14:08. Reply Matthew says: May 2, 2015 at 4:48 pm Cory, thanks for taking the time to comment. The machine will drain for 3 minutes before unlocking the door. 3. have a peek at this web-site

Whirlpool Washing Machine Error Code E1

Glad you got the washing machine back up and running. Check Pressure Switch for correct working with a DVM/VOM. 3. Verify CCU operation by running a Diagnostic Test or any cycle. F14 EEPROM error The Central Control Unit (CCU) receives it’s data from an EEPROM onboard the CCU.

Check the drive system for any worn or failed components. 5. Press PAUSE/CANCEL twice to clear the display. Unplug washer or disconnect power. 2. Whirlpool Range Error Code F9e0 Replace CCU board.

Loading... Verify CCU operation by running a Diagnostic Test or any cycle. Unfortunately, you have to replace it as an assembly on these units. http://www.appliancepartspros.com/repair-help/whirlpool-fault-codes.html Door switch/lock unit failure. 1.

This may signify a bad pump, an extra heavy load, excessive detergent, or excessive suds. Whirlpool Washer E1 F1 Error Code Reply Tony says: April 2, 2016 at 5:03 pm Jeff , check your water sensor. Let me know what happens if anything.. Unplug washer or disconnect power. 2.

Whirlpool Duet Dryer Error Code E1

Verify wire harness connections to inlet valves, pressure switch, flow meter, and Central Control Unit (CCU). 4. http://www.repairclinic.com/RepairHelp/How-To-Fix-A-Dryer/376-5-619505-/Whirlpool-E1-E2-Thermistor-Failure PUMP DRIVE ERROR The pump driver fails to activate. Whirlpool Washing Machine Error Code E1 Sign in to report inappropriate content. Whirlpool Top Load Washing Machine Error Codes Er Processor reset error This error code is displayed if the control failed to save cycle information during a power failure.

Check the drive motor for powered rotations. 6. More about the author F1 - Control Board Failure - Replace control board (clock). Reply Tom says: April 12, 2016 at 11:33 pm Thanks a ton. Refer to the Water Temperature Sensor section. Whirlpool Oven Error Codes

Press STOP/CANCEL to clear the display. ^ top LS Lid switch error The control should flash this error code if it cannot detect the lid switch opening and closing properly. Check connections of the CCU board within the housing. Unplug washer or disconnect power. 3. check my blog Am I supposed to remove the screws by the hinges?

Check wire harness connections to the dispenser motor and Central Control Unit (CCU). 4. Whirlpool Top Load Washer Error Codes I got this washer brand new for free so I've put up with it. If NTC is OK and failure repeats exchange steamer electronic board.

So, couple questions: Any idea what would cause items in the wash to get literally shredded to a pulp?

Check for continuity of the User Interface harness. 2. Opening the lid will allow you to view and redistribute the load. Check for continuity of the User Interface harness. 2. Whirlpool Microwave Error Codes Use drain hose form and attach securely to drainpipe or tub.

It has ripped up a few shirts and pants over the years (fortunately those didn't clog the filter). SUD - Suds Lock (Too Much Detergent Detected) - Make sure drain hose is not plugged or kinked and disconnect power and unplug unit. If you are a professional and see something I am doing wrong please feel free to leave constructive feedback in the comment section and feel free to refer your professional colleagues http://3cq.org/error-code/whirlpool-e1-f1-error-code.php Check wire harness connections to the dispenser motor and Central Control Unit (CCU). 4.

I was out of town when this happened. Matt Reply Tammy says: February 7, 2015 at 12:22 am Thank you for this, we found 3 socks in that darn filter. Verify the shipping system including shipping bolts, spacers and cables are removed. 2. This should have AC line voltage when the motor controller is powered.

Thought it was the suds from the soap according to Maytags website. No blockages there. Happy to help. I have a spare washer that has a bad heating element and temp sensor that I am using for parts.

Any of these drain hose issues can cause the washer to siphon (fills and drains at the same time) and the washer never fills to the expected level. LF - Long Fill - If the water fill time exceeds ten minutes, the water valves will be shut off and this error code will display. The drive motor must be hooked up properly or a "CE" error will occur. • Drive motor thermal protector has opened. • Motor controller is not powered or fuse has opened. Do not tape over drain opening.