Home > Error Code > Whirlpool E1 F2 Error Code

Whirlpool E1 F2 Error Code

Contents

there is a clip in each side of the black plastic receptacle (the place where the keytail plugs in on the electronics control board). the paper trick worked for me for about two weeks, then the problem happened again. NOTE: After 4 minutes the “Sud” error will be displayed, then 4 minutes later the F02 error code will be displayed. by JANET RUDISILL Earned 8 community points in Click'>Kenmore October 25th, 2015 Comment 0 votes Didn't find what you are looking for? have a peek at these guys

Unplug the unit and disconnect the power to check all wire harness connections to the inlet valve, pressure switch, drain pump, flow meter, and Central Control Unit (CCU). During that ~ 1 minute I have full control of the oven. We turned the breaker on and off as well as unplugged the oven didn't change. Jake Appliance Repair School 1987-1988 Star Appliance Tech. 2 yrs. 1988-1990 Wards Appliance Tech. 11 yrs. 1990-2001 Sears Appliance Tech. 4 yrs. 2001-Oct. 2005 Jake's Appliance Repair Nov. 2005-present Look-Up & more info here

E1-f2 Error Code Kenmore

Thank you for helping make our site better. 1-855-343-0066 Mon-Fri: 7am-1am EST Sat-Sun: 7am-11pm EST 1-888-738-4871 Mon-Fri: 7am-1am EST Sat-Sun: 7am-11pm EST Cart (0) Order Status Home Help Contact Instant Repairman™ This may signify problems with the drive motor, thermal protector or motor controller. The keypad for the white color range is 8272997. Is there an underlying cause that would have caused both the control panel and control board to go bad at the same time?

We purchased the house 4 years ago but it looks pretty new. If error code reappears then replace the touch pad, or touch pad and control board (clock) if all one assembly. Would not hurt to clean the connector on the board. Whirlpool Oven F2 Beeping F7-E1 - Common Switch Wire Is Defective - This error occurs when common wire to latch switch and door switch is shorted.

Turn off hot and cold water to faucets and unplug the unit before proceeding. E1 F2 Error Code Whirlpool Washer Have you ever purchased from PartSelect.com before? Credentials confirmed by a Fortune 500 verification firm. http://appliancejunk.com/forums/index.php?topic=1497.0 Make sure the harness does not have a faulty connection by checking the resistance values between serial communication pins with the connectors in place.

AppliancePartsPros.com is the registered trademark of AppliancePartsPros.com, Inc. Whirlpool Oven F1 Error Code E2 - Shorted Thermistor - Replace thermistor. That plastic ribbon cable is not always forgiving. Located on the bottom of the door latch assembly is a tear-drop shaped tab. 5.

E1 F2 Error Code Whirlpool Washer

I had so many questions and they answered them all." Sharon S. http://www.appliancepartspros.com/repair-help/whirlpool-fault-codes.html Use electronics contact cleaner or isopropyl alcohol and a tooth brush. E1-f2 Error Code Kenmore Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. 100% Satisfaction Guarantee Rate the answer you receive. Whirlpool Oven Error Codes See Details Related Pages Kenmore 5M followers Follow Appliances 164K followers Follow Ranges 628 followers Follow More Pages Wall Ovens 189 followers Follow Sweeps Personal Shopper Gift Registry Legal & Privacy

the next fix I tried was to unplug the keytail (the ribbon connector) from the slot on the control panel. More about the author Note: Applies to all F5-E... Ask Whrlp Master Tech Your Own Question Whrlp Master Tech, Whirlpool Master Technician Category: Appliance Satisfied Customers: 9084 Experience: 30 years Appliance Field 15 yr with Whirlpool Corp. 9 yrs Whirlpool Share it! Whirlpool Washing Machine Error Codes E1

I've tried the piece of paper behind the ribbon. Check wire harness connections to pressure switch, drain pump, and Central Control Unit (CCU). If error code reappears then replace the touch pad, or touch pad and control board (clock) if all one assembly. check my blog Press START to continue the cycle from the moment that power was lost.

All rights reserved. Wp8300440 While you are waiting for an expert to respond, I have attached a helpful link below that may provide information to assist you with your question. FL Flood condition "FL" flashes if any overfill condition occurs.

A magnifying glass helps here.

Press 'Stop/Cancel' to clear display. This should change to the F02 error code after a few minutes. Press 'Stop/Cancel' to clear the display. Whirlpool Oven F5 Click here for more information on other Whirlpool Parts from PartSelect.com Back to top Tweet PartSelect.com Home Contact About Us Help Privacy Policy Terms of Use Just For Fun!

View our Privacy Policy here. Once I return the control panel for $119.00 this would be the best financial choice. Category:Appliance Share this conversation Expert: built1950 replied7 years ago. http://3cq.org/error-code/whirlpool-e1-f1-error-code.php the paper trick worked for me for about two weeks, then the problem happened again.

Remember: Oven control (ERC) measures resistance of sensor circuit, not actual oven temperature. then I ordered the touchpad, but ended up fixing the problem before it arrived. Then it would come on. Clock display initially started going off by itself.

F3 Oven temperature sensor (RTD) open Replace Oven temperature sensor (RTD) F4 Oven temperature sensor (RTD) shorted Replace Oven temperature sensor (RTD) F5 Board failure Replace control board (also called ERC Flashing Display Time - Open Lid - This will only occur if the lid is opened during a running cycle. By reading any content on this site you agree to AppliancePartsPros.com , Inc. Kansas City, KS "Robin went above and beyond the call to assist me and I was very impressed." Val T.

Check the drive system for any worn or failed components and reconnect power and plug unit in. Note: If this error occurs, the door will remain locked and the drain pump will run constantly even if 'cancel' is selected. Electric Range - White See Details Kenmore 94153 5.4 cu. I did some research for you at Managemylife and found an expert answer to a similar question that may help until your expert can respond to your specific question.

To Manually unlock the door lock system: 1. codes.