Home > Error Codes > Whirlpool And Error Codes

Whirlpool And Error Codes


We must receive the returned part(s) with the Return Authorization number within 365 days of your original order date. Unplug washer or disconnect power. 2. Thermistor F0 E5 Unbalanced load Redistribute the load inside the spin basket. Rave Reviews "I thought it was the best online shopping experience that I have ever had when it comes to parts." Eric H. this content

CT Sat7:00 a.m. - 9:00 p.m.CT Sun7:30 a.m. - 9:00 p.m.CT Chat Local Store Availability Enter your zip code Find Store Sears PartsDirect uses your location to provide local availability Have you ever purchased from PartSelect.com before? Lid lock/switch assembly HC Hot and cold fill hoses are reversed Check the positions of the fill hoses on the back of the washer. The Sud or Sd code may alsobe the result of a restricted drain hose or standpipe (drainpipe).Make surethat the drain hose is not kinked or clogged. this contact form

Whirlpool Washer Error Codes F21

Verify CCU operation by running a Diagnostic Test or any cycle. Check wire harness connections between the drive motor and the Motor Control Unit (MCU), and b etween the MCU and the Central Control Unit (CCU). F64 STEAMER INLET VALVE FAILURE The Steamer valve or fl ush valve is blocked open or not working properly. F7 Function key stuck on ERC Replace control board (also called ERC or clock).

F70 CENTRAL CONTROL UNIT HEARTBEAT FAILURE If a Central Control Unit Heartbeat Failure is displayed, no communication is detected from the Central Control Unit to the User Interface. 1. If there are no stored errors 888 will be displayed with 3 beeps. FL Flood condition "FL" flashes if any overfill condition occurs. Whirlpool Washer Error Codes A10 F8 - Control Board Failure - Replace control board (clock).

It also means unplug the washer so you don't get electrocuted! If there's no wiring connection problem, the motor control board usually needs to be replaced. F32 PRESSURE SWITCH FAILURE If there is no electrical supply to the Pressure Switch from the CCU or if the Pressure Switch contacts are worn out, then a Pressure Switch Failure http://www.appliancepartspros.com/repair-help/whirlpool-fault-codes.html Instantaneous current trip occurs if there is a spike of 26 Amps instantly at the motor windings.

About Press Copyright Creators Advertise Developers +YouTube Terms Privacy Policy & Safety Send feedback Try something new! Whirlpool Duet Washer Error Codes F20 Measure door switch (door open = switch open small low voltage terminals). This may signify problems with the drive motor, thermal protector or motor controller. Open the console and check the wire harness connection between the main electronic control board and the user interface control board.

Whirlpool Top Load Washer Error Codes

Check the drive motor for powered rotations. 6. http://www.searspartsdirect.com/washer-repair/error-codes/whirlpool-duet-high-efficiency-front-load-washer-error-codes.html F1, F2, F6 Are main control and program faults. Whirlpool Washer Error Codes F21 Make sure there is not a siphon problem and check all hoses for possible leaks. Whirlpool Washing Machine Error Codes E1 Sign in to add this video to a playlist.

F1-E2 - UL A/D Error(s) - Disconnect power for at least 30 seconds and then reconnect. news If door latched: A. If failure still present: 3. Check the MCU by looking for operations of the drive motor. 7. Whirlpool Duet Dryer Error Codes

If there is NO water in the unit, make sure the valves are turned on all the way. Press STOP/CANCEL to clear the display. If corrections are made during any step, power should be reconnected and the unit should be tested. have a peek at these guys You can redistribute the load and start the washer.

Inlet water valve assembly F41 Motor RPS failure The motor RPS (Rotor Position Sensor) detects the speed of the drive motor. Whirlpool Dryer Error Codes If the motor is defective, replace it. Press PAUSE/CANCEL twice to clear the display.

HandySavesMoney 431,048 views 17:45 Whirlpool Fault Codes - Duration: 3:39.

If no damage to wires and all connectors okay, proceed to step C. Check wires and connectors from control to door switch, then from door switch to control. The wires should be to the left when facing the MCU connectors. 9. Whirlpool Top Load Washing Machine Error Codes LF - Long Fill - If the water fill time exceeds ten minutes, the water valves will be shut off and this error code will display.

This should clear the unit of the excess detergent. 1. Loading... F1E2 Error - Motor control fault. check my blog Try unplugging unit for two minutes to see if that fixes error.

F6E2 Error - Communication fault. Plug in washer or reconnect power. 4. If everything looks good, check for broken wires with a multi meter. If the basket spins properly, unplug the washer and check the wiring connections on the actuator.

Check calcifi cation of steamer element. Remove clothes from drum and start the cycle again. It will try to unlock the door 6 times before displaying the error. Door switch open while door is locked. 1.

This should change to the F02 error code after a few minutes. Once you are in the Duet washer's diagnostic mode and have recorded any errors that the washer has in it's little computer brain, press and hold the 3rd button used to Replace switch if defective. 4. dL (F80, F82, F84 or F85) Lid lock failure Check for debris in the lid lock mechanism that could prevent it from locking.

Door switch/lock unit failure. 1. Sign in Loading... Check wire harness connections to the MCU, the motor, and Central Control Unit (CCU). 4. Check sensor, sensor harness and sensor harness connection at sensor and oven control.

Watch QueueQueueWatch QueueQueue Remove allDisconnect Loading... If the lid lock/switch assembly won't lock and unlock properly, replace it. F06 STEAMER DEFECT The Steamer temperature has not reached the correct value. Drive motor, Main electronic control board F2 E1 Stuck key This code is for models with a digital display.

Opening the lid will allow you to redistribute the load to avoid a further off balance error.