Home > Error Codes > Whirlpool Duet F07 Error

Whirlpool Duet F07 Error

Contents

Check wire harness connections to the MCU, the motor, and Central Control Unit (CCU). 4. The doorswitch may cause an interference for the powersupply of the MCU. Ft. Check for stuck lock switch. have a peek at these guys

The control must realize that the trip was due to an overfill condition instead of a suds lock condition in order for "FL" to be displayed. Replace switch if defective. 4. This should clear the unit of the excess detergent. 1. If the condition continues four times, the F31 code will show 1.

Whirlpool Oven Error Codes

This error code may also be used if there is a disagreement between the motor and machine controllers on the state of the lid switch. The failure will be reset after running the Diagnostic Test Program. 1. Replace User Interface if drum is rotating. 4. F06 Drive motor tachometer error The control is unable to properly detect motor speed and the machine will shut down.

Instantaneous current trip occurs if there is a spike of 26 Amps instantly at the motor windings. Make sure the inner drum turns freely. (There may be some magnetic resistance (Magnetic Motor) but there should be no mechanical drag.)) (Duet Washer Motor Check) F8E0 Error - (Steam models) Electronic Board and the valve for steam fill. 4. Whirlpool Top Load Washing Machine Error Codes F02 Long Drain If the drain time exceeds 8 minutes, the water valves are turned off and F02 is flashed.

Check the MCU by looking for operations of the drive motor. 7. Whirlpool Washing Machine Error Codes E1 Check dispenser motor for powered rotations. Remove clothes from drum and start the cycle again. http://www.fixya.com/search/p438316-whirlpool_duet_ghw9150p_front_load/f07 Check wire harness connections to the dispenser motor and Central Control Unit (CCU). 4.

NOTE: After 4 minutes the “Sud” error will be displayed, then 4 minutes later the F02 error code will be displayed. Whirlpool 6th Sense Washing Machine Error Codes Remove the lower toe panel. 3. E., Cleveland, TN 37311 1-877-477-7278 AppliancePartsPros.com Customer Service 1-877-477-7278 Email Us Terms of Use Privacy Policy Site Map ©1999 - 2016 AppliancePartsPros.com. Full Answer The following are some of the error codes that appear on the Whirlpool Duet washer and dryer.F/06 Drive Motor Tachometer ErrorF/07 Motor Control Unit ErrorF/09 Overflow ConditionF/11 Serial Communication

Whirlpool Washing Machine Error Codes E1

Replace the Motor Control Unit. http://www.how-to-repair.com/help/whirlpool-washing-machine-wont-spin-f06-error-code-fault/ This should have AC line voltage when the motor controller is powered. Whirlpool Oven Error Codes FL Flood condition "FL" flashes if any overfill condition occurs. Whirlpool F07 Fault Code Repeat steps A and B for door switch. 3.

Potential Causes • Check the drain hose and make sure it is not plugged or kinked • Check Wire Harness connections to the Drain Pump, Pressure Switch, and Central Control Unit http://3cq.org/error-codes/whirlpool-and-error-codes.php The failure will reset after running the Diagnostic Test Program. 1. Press CANCEL and observe for 1 minute to ensure operation is correct. 2. Check wire harness connections to the MCU, the motor, and Central Control Unit (CCU). 4. Whirlpool Microwave Error Codes

Potential Causes • Check the drain hose and make sure it is not plugged or kinked • Check the electrical connections at the pump and make sure the pump is running. NOTE: To find correct Ohm reading refer to the Water Temperature Sensor section. 1. Verify the shipping system including shipping bolts, spacers and cables are removed. 2. check my blog Terry and Jo RV-Dreams Family Member Status: Offline Posts: 4933 Date: 08:12 PM Apr 1, 2014 Permalink We've also had some problems with our Whirlpool, but I suspect our problem was

Replace User Interface. Whirlpool Top Load Washer Error Codes Check if the airtrap is not blocked. 3. Plug in washer or reconnect power. 6.

Plug in washer or reconnect power. 5.

Ours lasted 3 years before we discarded and replaced it. Also, check the wire harness connections between the MCU and the central control unit (CCU). If a failure occurs during high-speed spin the door will be unlocked after 3 minutes. Whirlpool Duet Dryer Error Codes Press PAUSE/CANCEL two times to clear the display. 1.

F24 WATER TEMPERATURE SENSOR ERROR If the water temperature sensor (NTC) value is out of range (23°F to 217°F[-5°C to 103°C]) during the water-heating step of the WASH cycle. Check resistance of heating element, if present on this model. (abnormal = infinity) 4. Door switch/lock unit failure. 1. news This condition occurs when excessive water in the tub causes the overfill switch to trip.

If this happens, replace oven control (also called clock or ERC). 2. French Door Bottom-Freezer Refrigerator with EasyFill Internal Water Dispenser Range 30" Freestanding Electric Range with a 5.4 Cu. F20 NO WATER DETECTED ENTERING MACHINE OR PRESSURE SWITCH TRIP NOT DETECTED. Potential Causes • Check Wire Harness connections to the MCU, the motor, and Central Control Unit (CCU) • Check Drive belt • Check MCU • Check Motor • Check Wire Harness

Verify inlet valve operation. If a failure occurs during high-speed spin the door will be unlocked after 3 minutes. If you get this error... 1. The pump is cycled in drain mode for 30 seconds on, 30 seconds off until the overfill switch resets or power is discontinued to the unit.

In an Overflow condition, the Door will remain locked, and the Drain Pump will run constantly, even if PAUSE/CANCEL is pressed twice and the Display is cleared. Mismatch of User Interface and CCU or corrupted EEPROM. 1. Ft. The wires should be to the left when facing the MCU connectors. 9.

F5 - E6 Door is open, but latch is locked F5 - E7 Self clean latch will not unlock F6 - E0 Return line not connected If switch pulse return line If failure remains, disconnect power and replace control.