Home > Error Codes > Whirlpool Elite Washer Error Codes

Whirlpool Elite Washer Error Codes

Contents

Unplug the washer and, if the washer is overfilled, check the water inlet valve assembly for proper shut-off of water flow. Door not opened during 3 consecutive cycles. 1. Short circuit of Heater to Ground. All of our chat agents are currently assisting other customers. have a peek at these guys

Unplug washer or disconnect power. 3. Short circuit of Heater to Ground. To manually unlock the unit, unplug the power cord from the outlet and remove the toe panel. NOTE: Detects by weight. http://applianceassistant.com/Washer-Repair/Duet/Duet-Washer-Error-Codes.php

Whirlpool Duet Washer Error Codes F21

Had been told was motor control board. $200 in parts & $130 in labor. F03 HEATER SC TO GROUND The Heater has a internal short circuit. Check for plugged or kinked inlet hoses or plugged screens in the inlet valves. Check the harness between the Steamer and the Steamer Electronic board. 3.

If a failure occurs during high-speed spin, the door will be unlocked after 3 minutes. Replace User Interface if drum is rotating. 4. F/10 Motor control board overheated Unplug the washer and check the wiring connections on the motor control board. Whirlpool Duet Washer Error Codes F02 F25 DRIVE MOTOR TACHOMETER ERROR If the control is unable to properly detect motor speed, the machine shuts down.

Plug in washer or reconnect power. 5. Whirlpool Duet Washer Error Codes F20 F11 Serial communication error Communication between the Central Control Unit (CCU) and the Motor Control Unit (MCU) cannot be sent correctly. Check wires and connectors from control to door switch, then from door switch to control. Door switch/lock unit failure. 1.

Sign in to add this to Watch Later Add to Loading playlists... Whirlpool Duet Dryer Error Codes Door Lock Mechanism broken or removed from the Door Check Door Lock/Switch Assembly Check the wire harness connections to the Door Lock/Switch Assembly and Central Control Unit (CCU) Door Lock/Switch Assembly If there is no water in the unit: Make sure that both valves at the water source(s) are turned on all the way. You will also want to check the pressure sensor (Duet Washer Pressure Sensor Check) F3E2 Error - Temperature sensor fault.

Whirlpool Duet Washer Error Codes F20

Check for loose connectors. 3. http://www.repairclinic.com/RepairHelp/FaultCodes/50/Duet-Duet-HT If present, replace control board (clock). Whirlpool Duet Washer Error Codes F21 F09 - Overflow Condition (Pressure Switch Closed Too Long) - Check to make sure drain hose is not plugged or kinked and unplug the unit and disconnect power. Whirlpool Top Load Washer Error Codes Heck, even your typical PC has a higher case temperature than the 120-140 degrees of an average household's hot water system… Reply jane says: June 8, 2016 at 2:48 pm Wow!

Electronic Board and the valve for steam fill. 4. More about the author F8E3 Error - Overflow fault. If after 30 seconds the control does not detect water entering machine and then valves will be turned off and the error code will be displayed. Check the drain hose and make sure it is not plugged or kinked. 2. Whirlpool Duet Reset

A: Whirlpool Duet products and parts can be purchased at big box stores, such as Best Buy, or via online retailers, such as Amazon. If there are no stored errors 888 will be displayed with 3 beeps. Check for plugged or kinked inlet hoses, as well as plugged screens in the inlet valves. check my blog Replace failed component.

Loading... Whirlpool Washer Error Codes 5d The door may now be opened. ^ top Find Parts Whirlpool Duet Front Loading Gas and Electric Dryer Fault Codes Failure Code Fault Code Description Solution PF Power failure "PF" flashes This may signify a bad pump, an extra heavy load, excessive detergent, or excessive suds.

Check wire harness connections to the dispenser motor and Central Control Unit (CCU). 4.

Repeat steps A and B for door switch. 3. Close the lid and press 'Start' to continue. Unplug the washer and check the mechanical linkage on the dispenser housing. Whirlpool Duet Sport Washer Error Codes Check/clean drain pump filter of foreign objects. 5.

Check the electrical connections at the pump and make sure the pump is running. 4. If failure still present: 3. This should clear the unit of the excess detergent. 1. http://3cq.org/error-codes/whirlpool-washer-troubleshooting-error-codes.php Unplug washer or disconnect power. 3.

F30 DISPENSER SYSTEM ERROR When the dispenser motor cannot be driven to its proper position. 1. Replace Central Control Unit if drum is not moving F71 USER INTERFACE HEARTBEAT FAILURE If a Central Control Unit Heartbeat Failure is displayed, no communication is detected from the User Interface If, at any time during this continuous process of passing data back and forth an error is discovered during the handshaking, the CCU throws a serial communications error. Check for drain pump failure. 6.

F2-E0 - Shorted Touch Pad (Keypad) - Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure. Press STOP/CANCEL to clear the display. In normal use (a little blockage is normal) the steamer cleans itself. F03 HEATER SC TO GROUND The Heater has a internal short circuit.

LS - Lid Switch Error - This error will occur if unit cannot detect the lid switch opening or closing. F5 - Control Board Failure - Replace control board (clock). Check the connections between the Steamer 3. Check the wire harness connection between the motor control board and the main control board.

Plug in washer or reconnect power. 6. Plug in washer or reconnect power. 4. If NTC is OK and failure repeats exchange steamer electronic board. Allow at least a minute after power has been restored and if error code reappears, replace control board (clock).