Home > Error Codes > Whirlpool Error Codes Washer

Whirlpool Error Codes Washer

Contents

Check the inlet valve and pressure switch for proper shut off and operation. This is normally due to a faulty door interlock switch or wiring issue. F25 DRIVE MOTOR TACHOMETER ERROR If the control is unable to properly detect motor speed, the machine shuts down. Possible Causes/Procedure Door lock mechanism is broken or removed from door. have a peek at these guys

Make sure the harness does not have a faulty connection by checking the resistance values between serial communication pins with the connectors in place. Replace failed component. Refer to the Water Temperature Sensor section. F28 SERIAL COMMUNICATION ERROR The communication between the Central Control Unit (CCU) and the Motor Control Unit (MCU) cannot be sent correctly. 1.

Whirlpool Washer Error Codes F21

F2 will appear. Is there a different sequence for this machine? None of the buttons on the control pad work. Repeat steps A and B for door switch. 3.

Replace heater. You have not opened to door for 3 wash cycles… (Too many Margarita!?) 3. If everything looks good, check for broken wires with a multi meter. Whirlpool Washer Error Codes A10 Replace failed component.

F6-E0 - Return Line Not Connected - This error should appear within 60 seconds after power up to appliance. Whirlpool Top Load Washer Error Codes With an overfill condition, the beeper repeats a warning every 10 seconds with no time out. F5 - E0 Door switches do not agree (condition exists when door switch is closed indicating an open door, and latch switch is closed indicating a locked door) 1. http://www.searspartsdirect.com/washer-repair/error-codes/whirlpool-duet-high-efficiency-front-load-washer-error-codes.html Nest® and Nest Learning Thermostat™ are trademarks licensed by Nest Labs, Inc.

Is it possible you overloaded the washer? Whirlpool Washer Diagnostic Mode F13 - Dispenser Circuit Error - Disconnect power and unplug unit to check mechanical linkage from dispenser motor to top of dispenser. Check Motor for any signs of damage Check main control unit by running test program Whirlpool advise that if failure occurs with universal motor, replace control unit but if the washing Replace MCU board.

Whirlpool Top Load Washer Error Codes

If door latched: Disconnect power from unit. http://www.appliancehelponline.com/whirlpool.html More Whirlpool Washing Machine Help Should you need more help and guidance please use the links from this article as most of them will help you to understand your Whirlpool washing Whirlpool Washer Error Codes F21 You need to find a washer... Whirlpool Duet Dryer Error Codes Make sure all grounding switches are engaged. 3.

Verify CCU operation by running a Diagnostic Test or any cycle. 6. More about the author Level the machine. Check wire harness connections to the door switch/lock unit and Central Control Unit (CCU). 4. Getting error code F1.Reply 126 DIY Project Help Tips December 16, 2015 at 6:33 pmNag, If your Whirlpool washing machine is showing the F1 error code this means the control board Whirlpool Duet Washer Error Codes F20

F7 - Function Key Stuck - Replace control board (clock). what is the remedy. NOTES: After 4 minutes the “Sd” error will be displayed, then 4 minutes later the “F/21” error code will be displayed. http://3cq.org/error-codes/whirlpool-washer-troubleshooting-error-codes.php If there is no water in the unit: Make sure that both valves at the water source(s) are turned on all the way.

C. Whirlpool Washing Machine Error Codes E1 Clear Stored Duet Error & Fault Codes Not all washer made by Whirlpool have the ability to clear error code memory. If a failure occurs during high-speed spin, the door unlocks after 3 minutes. 1.

How To Easily Clean A Dirty Oven That Has Never Been Cleaned February 17, 2016 Maytag Dishwasher Error Codes HE Models - Lights Flashing Blinking - What To Check?

The door lock is not locked whilst the failure is displayed. F1E1 Error - Main control fault. Not even 0.1 L of water has entered the tub from the first 30 seconds of the Duet Washer Quick Test… Is the water turned on? Whirlpool Duet Washer Error Codes F02 If the above does not correct the problem, go to step 7. 7.

Ask your question below and we will be happy to assist.Related DIY Articles That May Assist You... After the wash cycle , it just stops . If you can’t look through it, exchange Steamer. 5. news Irvington, NY "I LOVE seeing customer service excellence, seeing follow through on promises." Gregory R.

F2-E5 - Cancel Key Line Open - Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure. Sr Lid switch error The control should flash this error code if it cannot detect the lid switch opening and closing properly. F3 Oven temperature sensor (RTD) open Replace Oven temperature sensor (RTD) F4 Oven temperature sensor (RTD) shorted Replace Oven temperature sensor (RTD) F5 Board failure Replace control board (also called ERC October 17, 2016 Blomberg Washing Machine Error Codes October 15, 2016 TV Screen Is Green - What To Check - How To Fix?

This condition occurs when excessive water in the tub causes the overfill switch to trip. Thank you for helping make our site better. 1-855-343-0066 Mon-Fri: 7am-1am EST Sat-Sun: 7am-11pm EST 1-888-738-4871 Mon-Fri: 7am-1am EST Sat-Sun: 7am-11pm EST Cart (0) Order Status Home Help Contact Instant Repairman™ Ld Long drain "Ld" flashes if it takes longer than 5 minutes to pump out water to a point where the operating pressure switch resets. Check if the airtrap is not blocked. 3.

Unplugged the washer and the humming noise started again. Check all wiring and connectors between the main electronic control unit and user board Check display module (most likely sue to damage or spillage etc) Check main control unit F22 Check wire harness connections to the User Interface and the Central Control Unit. 3. If none of this works you may have an issue with the water inlet solenoids.

F8 Faults are water related… valve, dispensing system, water level, steam valve, and flow meter problems. Reply Quote paul horner 1 year 4 months my whirlpool aquastream has fault f06what does it need to fix if and can u send me a diagram ?? Carl says : Reply September 12, 2016 at 10:31 pm I have an AWO 3560. You will also want to check the pressure sensor (Duet Washer Pressure Sensor Check) F3E2 Error - Temperature sensor fault.

I have a Whirlpool AWO/C72200. July 3, 2015 DIY Raised Garden Bed With Landscaping Timbers July 1, 2015 How To Divert Water Dripping Outside From Air Conditioner Window Unit June 30, 2015 Water Heater Preventive Maintenance The relay might be soldered or always open.