Home > Error Codes > Whirlpool Washer Error Codes

Whirlpool Washer Error Codes

Contents

Press CANCEL and observe for 1 minute to ensure operation is correct. 2. Cause: water is overflowing (water level frequency is over (213) When FE is diplayed the drain will pump out automatically. "PE" Pressure sensor error. Press PAUSE/CANCEL twice to clear the display. If too much detergent was used: – Run the unit through a RINSE/SPIN cycle. – Run a NORMAL cycle without adding any detergent. have a peek at these guys

F10 - Motor Control Unit (MCU) Heat Kink Thermal Trip (Too Hot) - Check for proper installation and ventilation, and make sure unit is not located near a heat source. F1 - Control Board Failure - Replace control board (clock). F33 PUMP DRIVE SYSTEM ERROR When the connection between pump and the Central Control Unit (CCU) is lost. 1. If that works the your pump is highly suspect.

Whirlpool Duet Washer Error Codes F21

The failure will reset after running the Diagnostic Test Program. 1. If after 30 seconds the control does not detect water entering machine and then valves will be turned off and the error code will be displayed. F02 Long Drain If the drain time exceeds 8 minutes, the water valves are turned off and F02 is flashed.

Check mechanical linkage from dispenser motor to the top of the dispenser. 3. Check the resistance across the the two pump terminals with an ohm/voltage meter. Check the drive motor for powered rotations. 6. Whirlpool Duet Washer Error Codes F02 If connections are ok, then check individual switches as outlined for the F5 error code.

Check the drive system for any worm or failed components and reconnect power and plug unit in. Whirlpool Duet Washer Error Codes F20 Press and HOLD start to continue the cycle, or press 'Stop/Cancel' to clear display and cancel cycle. Note: Applies to all F1-E... It can also indicate a bad pump, an extra heavy load, excessive detergent, or excessive suds.

Circuit Board Medics can eliminate these errors with upgrades to the CCU. Whirlpool Duet Dryer Error Codes Allow at least a minute after power has been restored and if error code reappears, replace control board (clock). If a failure occurs during high-speed spin the door will be unlocked after 3 minutes. This may signify a bad pump, an extra heavy load, excessive detergent, or excessive suds.

Whirlpool Duet Washer Error Codes F20

If door is NOT latched, disconnect power from unit and check wires and connections. http://www.appliancepartspros.com/repair-help/whirlpool-fault-codes.html Whirlpool Duet Drain Pump Test Unplug or disconnect power from the washer. Whirlpool Duet Washer Error Codes F21 Check the drain hose and make sure it is not plugged or kinked. 2. Whirlpool Top Load Washer Error Codes Disconnect power and unplug the unit to check wire harness connections to the motor, MCU, and Central Control Unit (CCU).

If you get this error... 1. More about the author Sign in to report inappropriate content. It will try to unlock the door 6 times before displaying the error. Have you ever purchased from PartSelect.com before? Whirlpool Duet Reset

They use the status lights on the touchpad/LED. Press STOP/CANCEL to clear the display. F3 faults are washer sensor related problems. http://3cq.org/error-codes/whirlpool-washer-troubleshooting-error-codes.php Potential Causes • A power glitch may cause this error.

Your satisfaction is guaranteed or you receive an account credit

© Copyright 2015 Tech Answers Live Become and expert How It Works Terms Of Use Whirlpool Washer Error Codes A10 Check mechanical linkage from dispenser motor to the top of the dispenser. Your Duet washer was not able to unlock after 6 tries.

Press STOP/CANCEL to clear the display. "CA" "Cl" Average current limit Or Instantaneous current limit If a status signal comes back from the motor controller that a current limit has been

Replace defective part. If the above does not correct the problem, replace the pump. "F/05″ Water Temperature Sensor Error

If during the water heating step in wash cycle, the water temperature sensor (NTC) value PUMP DRIVE ERROR The pump driver fails to activate. Whirlpool Duet Washer Error Codes F H F7 Function key stuck on ERC Replace control board (also called ERC or clock).

F06 Drive motor tachometer error The control is unable to properly detect motor speed and the machine will shut down. Press STOP/CANCEL to clear the display. Check/clean drain pump filter of foreign objects. 5. news Press START to continue the cycle from the moment that power was lost.

Check wires and connectors from control to door switch, then from door switch to control. If too much detergent was used, run the unit through a Rinse/Spin cycle, and then run a Normal cycle without adding detergent. If a potential suds lock is detected, the control tries up to 3 times to clean out the unit with a mini-cycle. "SL" is displayed if suds are detected but the See the repair guide to fix it yourself Motor control board, Wiring harness F/11 Serial communication error between main electronic ontrol board and motor control board Check the connections on the

Gently pull the tab down approximately 1/4 inch or until a 'click' is heard. Potential Causes • Check mechanical linkage from dispenser motor to the top of the dispenser. • Check Wire Harness connections to the dispenser motor and Central Control Unit (CCU) • Check F8E3 Error - Overflow fault. NOTE: Detects by weight.

See Manually Unlocking The Door Lock System. Cause: the thermistor is out of order. Check sensor, sensor harness and sensor harness connection at sensor and oven control. C.L.S.

F2 - E1 Keypad cable unplugged F2 - E5 Cancel key drive line open F2 - E6 Cancel key drive line open F3 - E0 Oven temperature sensor (RTD) opened (upper Check the drain hose and make sure it is not plugged or inked. ApplianceVideo.com 89,621 views 57:28 Troubleshooting the F35 Sud Error Code in the Whirlpool Duet Steam Washer - Duration: 12:49. Check wire harness connections to the drain pump, pressure switch, and Central Control Unit (CCU). 4.

Verify wire harness connections to inlet valves, pressure switch, flow meter, and Central Control Unit (CCU). 4. To manually check the function of the Pressure Switch, remove hose from switch and apply air to switch. Like ApplianceAssistant on Facebook!