Home > Error Codes > Whirlpool Washers Error Codes Duet

Whirlpool Washers Error Codes Duet

Contents

Check that the serial harness at the MCU is not mounted upside down. F/05 Water Temperature Sensor Error If during the water heating step in wash cycle, the water temperature sensor (NTC) value is out of range, or the heating element circuit has failed, Unplug washer or disconnect power. 3. Cart0 Your Shopping Cart Checkout Now PartsQuantity Total items: 0 View Entire Cart Your shopping cart is empty. have a peek at these guys

This error code may also be used if there is a disagreement between the motor and machine controllers on the state of the lid switch. Potential Causes • Door Lock Mechanism broken. • Check Door Lock/Switch Assembly for foreign objects • Check Wire Harness connections to the Door Lock/Switch Assembly and Central Control Unit (CCU) • codes. Check for drain pump failure. 6.

Whirlpool Duet Washer Error Codes F21

See the repair guide to fix it yourself Door lock assembly F/dU Door unlock error The washer won't unlock. Check the drain hose and make sure it is not plugged or kinked. 2. It will try to unlock the door 6 times before displaying the error.

Possible causes… 1. F13 Dispenser circuit error If the dispenser motor is not able to be driven to it’s proper position. Unplug washer or disconnect power. 3. Whirlpool Duet Dryer Error Codes Verify wire harness connections to inlet valves, pressure switch, drain pump and Central Control Unit (CCU). 5.

Try unplugging the washer for a minute and putting the washer through a quick diagnostic test and see what you get… In some cases this can reset the control and buy Whirlpool Duet Reset FdU Door unlock error A Door Unlock Error occurs if the door cannot be unlocked. Replace sensor if found defective. Verify inlet valve operation.

F13 Dispenser circuit error If the dispenser motor is not able to be driven to it’s proper position. Whirlpool Duet Washer Error Codes F02 Close Chat is currently unavailable We're sorry! Disconnect power from unit. The filter had coins, pencils, a wire from a bra, and a piece of cloth that was stuck in the pump impeller vanes.

Whirlpool Duet Reset

Limit $10 in points per member. http://www.techanswerslive.com/appliances/whirlpool-duet-washer-error-code-f9-e1-long-drain/13/ If too much detergent was used: Run the unit through a RINSE/SPIN cycle. Whirlpool Duet Washer Error Codes F21 Check the drive motor for powered rotations. Whirlpool Duet Washer Error Codes F20 Unplug washer or disconnect power.

If after 30 seconds the control does not detect water entering machine and then valves will be turned off and the error code will be displayed. More about the author Disconnect power for at least 30 seconds. 2. F1 - E1 EEPROM checksum error F1 - E2 UL A/D error(s) F1 - E4 Model ID error F1 - E4 Model ID error F1 - E5 Calibration shifted F1 - Stinky Duet Washer Whirlpool has made big improvements with the new Duet washers to reduce odors with an improved venting system. Whirlpool Top Load Washer Error Codes

Plug in washer or reconnect power. 6. If after 30 seconds the control does not detect water entering machine and then valves will be turned off and the error code will be displayed. Close the lid and press START to continue with the cycle. http://3cq.org/error-codes/whirlpool-front-load-washers-error-codes.php F42 MOTOR CONTROL UNIT FAILURE - REPETITIVE UNDERVOLTAGE The Motor Control Unit continuously checks for voltage.

Check the wire harness connections to the door switch/lock unit and Central Control Unit (CCU). Whirlpool Duet Sport Washer Error Codes Check Wire Harness connectors to the MCU, the motor, and Central Control Unit (CCU) Check Drive belt Check MCU Check Motor Check Wire Harness Sud SUDS LOCK (Overdose of Detergent detected Press PAUSE/CANCEL twice to clear the display.

Duet Washer Diagnostics Mode Back to Top You May Also Like...

ApplianceVideo.com 85,483 views 4:11 How to Diagnose Washing Machine Control and Program Problems - Duration: 9:08. F1E1 Error - Main control fault. NOTE: During first power up of new CCU and UI combination, a bootphase (uploading parameters) will be performed. Whirlpool Washer Error Codes 5d F3 faults are washer sensor related problems.

If there is no water in the unit: 1. Replace failed component. ^ top F15 Motor Control Unit (MCU) error If the MCU detects multiple resets or errors during a wash cycle it will go into this error mode. Appliance tip of the week older posting all gathered together to help YOU out! news If the condition continues four times, the F31 code will show.MCU FAILURE If the heat sink gets too hot, the Motor Control Unit (MCU) will stop the motor, the MCU will

Unplug washer or disconnect power. 2. If there is no water in the unit: Make sure that both valves at the water source(s) are turned on all the way. Check Wire Harness connectors to the MCU, and Central Control Unit (CCU) Check the Drive system for any worn or failed components Check MCU Check Motor F/11 Serial Communication Error Communication It will try to unlock the door 6 times before displaying the error.

Potential Causes • Check wire harness connections between the Drive Motor/Tachometer and the Motor ControlUnit (MCU), and between the MCU and the Central Control Unit (CCU) • Check the Drive Motor Check the pressure switch. 8. Door Lock Mechanism broken. Check the MCU by looking for operations of the drive motor. 7.

Enjoy bottle-quality water without the added waste (stays the same) Automatic Reorder About SYWR Get rewarded for shopping. Remove the lower toe panel. 3. Well that happens, a little too frequently if you ask me... If there is an error reading this data it will cause this error.

Unplug washer or disconnect power. 3. Replace switch if defective. 4. Click here to visit Merchant's home page. Er Processor reset error This error code is displayed if the control failed to save cycle information during a power failure.

Shop HalloweenCostumes.com for Suicide Squad costumes and accessories. Check connections of the CCU board within the housing.