Home > Western Digital > Western Digital 0223 Error Code

Western Digital 0223 Error Code

Contents

Check cabling and retest. Error logging capability: (0x01) Error logging supported. enabled help you monitor a drive's internal status through diagnostic commands. Drive should be replaced. http://3cq.org/western-digital/western-digital-error-code-0223.php

Replace the drive if the error repeats. I see your point, but the question is about two diagnostic tools gives two different results and I have no clue which one is more correct than the other one. –Antonio Retest after checking the connections. Replace Drive 211 2-9 Uncorr ECC Errors Error Correction Code (ECC) 2 through 9. why not find out more

Western Digital Error Codes

Re-Test Drive 106 Track 0 Error Track 0 was not properly detected. Replace the drive if the error repeats. If the automatic repair feature is unable to repair these errors, replace the drive.

General Purpose Logging supported. Re-Test Drive 17 Erase SSD Failure A write command during the test has failed. It also may be due to a defective connection. This may be due to a media or read error.

Retest and replace the drive if the error repeats. Western Digital Error Code 0007 Replace the drive if the error repeats. Re-test Drive 144 THIRD STROKE ERROR Error encountered during 1/3 stroke seek. Check connections and retest.

If the system cannot properly handle a drive running a specific Ultra ATA rate such as ATA100, the data may become corrupted. Retest after checking the connections. Re-test Drive with appropriate diagnostic utility 202 Drive Not Supported Older Western Digital drives are not supported by the diagnostic utility version being used. This may be due to a defect.

Western Digital Error Code 0007

not all smart errors are created equal, but growth in bad blocks tends to approach exponential over time. I did a fresh re-install of Win7 yesterday, but the problem did not go away, so I thought my HD or RAM may have gone bad. Western Digital Error Codes Hot Network Questions Seasonal Challenge (Contributions from TeXing Dead Welcome) What's this I hear about First Edition Unix being restored? This may be an anomaly or a defect with the drive.

This may be an anomaly or a defect with the drive. navigate here If Selective self-test is pending on power-up, resume after 0 minute delay. Ensure that you are using the latest version of diagnostic utility and that your cable is in good working condition. Please rate the helpfulness of this answer Answers others found helpful Understanding S.M.A.R.T.

After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 61 00 00 00 00 40 Commands leading to the This may be due to a media error. The same utility and the original code used to lock the drive are necessary to unlock this drive. http://3cq.org/western-digital/western-digital-hard-drive-error-code-0223.php Register now!

I've completely cleaned the PC of dust and even re-applied thermal compound on my CPU to make sure it wasn't a heat issue. Re-test with appropriate diagnostic utility 222 Drive Failed the Test Self-Monitoring, Analysis, and Reporting Technology (SMART) Error returned during SMART Status/Self Test Command. To run in ATA 66 and ATA100 rates, an Ultra ATA 80 -conductor cable must be used.

I would be happy if the drive would reallocate these sectors, but going by smart status it is not doing that.

Retest after checking the connections. Back to top #6 Broni Broni The Coolest BC Computer BC Advisor 41,243 posts OFFLINE Gender:Male Location:Daly City, CA Local time:02:25 AM Posted 14 March 2010 - 07:06 PM Do Please re-test the drive with Data Lifeguard. There may be repairable media errors on a platter.

Going to try and install pfSense now.. Replace Drive 213 2-9 DAM Errors Data Address Mark (DAM) 2-9. Further errors indicate a defective drive. http://3cq.org/western-digital/western-digital-error-0223.php I kinda figured...

Replace Drive 215 2-9 IDNF Errors Identified Data Not Found (IDNF) 2-9. Non-WD drives are not supported. Check cabling & retest. Contact System Vendor 221 Test Not Supported Certain older drives do not support certain SMART Self Tests.

Retest the drive with Data Lifeguard. Replace the drive if the error repeats. Replace the drive if the error repeats. This is to avoid bad sectors that can not be replaced by backup sectors (non-existent).

Please ensure that you are using the version of diagnostic utility corresponding to either newer or older Western Digital drives. The drive should now be defect free. Back to top #15 cryptodan cryptodan Bleepin Madman Members 21,868 posts OFFLINE Gender:Male Location:Catonsville, Md Local time:09:25 AM Posted 15 March 2010 - 06:40 PM Have you experienced any power Check cabling and retest.

Re-test with appropriate diagnostic utility 222 Drive Failed the Test The drive has failed the SMART test. Re-Test Drive 104 Drive Not Ready The drive did not properly respond to test commands. Retest after checking the connections. Drive should be replaced.

Several instances of information on data positioning and location could not be found. Drive should be replaced.