Home > Western Digital > Western Digital 0226 Error Code

Western Digital 0226 Error Code

Use the appropriate version. Re-Test Drive 106 Track 0 Error Track 0 was not properly detected. Re-Test Drive 6 SMART Diagnostic Self-Test (DST) Failure Self-Monitoring, Analysis, and Reporting Technology (SMART) Self-Test Command failed. Check cabling & retest. http://3cq.org/western-digital/western-digital-error-code-0226.php

The drive has detected an unstable condition, possibly an incorrect spin speed. Show Ignored Content Page 1 of 2 1 2 Next > As Seen On Welcome to Tech Support Guy! But... If the errors continue, replace the drive.

This may be an anomaly or a defect with the drive. It had been running slowly/coming up with some errors, so I was scanning it for viruses when it restarted randomly. I used Ontrack that comes on the boot CD.

Re-Test Drive 104 Drive Not Ready The drive did not properly respond to test commands. Replace the drive if the error repeats. Replace Drive 457 IDNF 2-9 Identified Data Not Found. Why is the FBI making such a big deal out Hillary Clinton's private email server?

Will I encounter any problems as a recognizable Jew in India? Update: S.M.A.R.T. === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Green (AF) Device Model: WDC WD10EARS-00Y5B1 Serial Number: WD-WCAV******** LU WWN Device Id: 5 0014ee 259379483 Firmware Version: i_hate_flyingSep 6, 2009, 10:31 AM I know what the problem is now, but I have no idea how to fix it. Replace the drive if the error repeats.

The drive is defect free. Re-Test Drive 108 Seek Not Complete A Seek command did not complete in the time allotted. Spinrite is too, but when I run it the program gets to the point where it starts reading the drive and then that clicking noise starts putting Spinrite into an eternal SERVO is data on track location.

Several instances of track information could not be found. http://en.community.dell.com/support-forums/laptop/f/3518/t/19355592 The command set to be executed has timed out. Ten or more instances of information on data positioning and location could not be found. The drive spins up and spins down just fine, but it goes into that accessing clicking loop very soon (seconds) after I try to boot from the drive or access files

Drive should be replaced. http://3cq.org/western-digital/western-digital-hdd-error-0226.php Replace the drive if the error repeats. Retest after checking the connections. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always

Please re-test the drive with Data Lifeguard. Reseating all of the drive cables is an excellent suggestion - definitely try that first before trying to freeze the drive. Says Hiren's boot CD contains this, but I don't see it anywhere in the menus. Check This Out BIOS recognizes the drive.

That seems to me the only way to confirm the HDD can be accessed or not. Replace Drive 200 Drive Not Tested Supported WD drives are initialized with this status. This is a monitoring system, which stores all errors, retries, and power on hours.

Computers with S.M.A.R.T.

Re-test with appropriate diagnostic utility 222 Drive Failed the Test Self-Monitoring, Analysis, and Reporting Technology (SMART) Error returned during SMART Status/Self Test Command. to report if a drive has failed, it must be enabled as a system option. Replace the drive if the error repeats. I have successfully accessed bios, and told it to boot from the CD, but it will not do this.

why not buy a Vantec hard drive dock and another large capacity drive (1 terabyte samsung or WD) , then remove all drives from your computer, install your OS on the Please re-test the drive with Data Lifeguard. This may be due to a defect with the drive or a bad connection. this contact form Drive should be replaced.

Replace. The other internal drive I'm using is a WD 1 TB for media and whatnot. This may be due to a media error. One instance of track information could not be found.

That would pretty much be all I need, and then I could just replace the drive. See what happens now. Retest after checking the connections. Esker" mean?

It also may be due to a defective connection. It also may be due to a defective connection. No Errors 101 Unknown Error An unknown error has occurred during testing. It seems that a portion of the disk is physically damaged.

There were too many errors found on this drive to be repaired.