Home > Western Digital > Western Digital Error Code 0008

Western Digital Error Code 0008

Here is the output from Minitoolbox. How Does a computer get Infected? Offline surface scan supported. Sign up now! have a peek here

Auto Offline data collection on/off support. Retest after checking the connections. I see your point, but the question is about two diagnostic tools gives two different results and I have no clue which one is more correct than the other one. –Antonio Replace your cable and retest the drive. https://support.wdc.com/knowledgebase/answer.aspx?ID=11711

This is a monitoring system, which stores all errors, retries, and power on hours. Replace drive if unable to correct error 118 DAM Error Data Address Mark (DAM) Error. Error: (08/20/2014 03:02:59 PM) (Source: ESENT) (User: ) Description: wuauclt (768) An attempt to open the file "F:\WINDOWS\SoftwareDistribution\DataStore\Logs\edb.log" for read only access failed with system error 32 (0x00000020): "The process cannot No Errors 100 No Errors Found Successful operation.

Drive should be replaced. Return to Top In case the answer did not answer your question, you can always visit the WD Community for help from WD users. Suspend Offline collection upon new command. Replace.

Replace Drive 557 SERVO 2-9 SERVO is data on track location. There were media errors that were within the repair capabilities of diagnostic utility. This may be due to a media error. http://support.wdc.com/classic/techinfo/general/errorcodes.asp?lang=ls%22 Short self-test routine recommended polling time: ( 2) minutes.

Several instances of information on data positioning and location could not be found. Good Luck Roger Fortune Cookie says: Fortune not Found: Abort, Retry, Ignore? Please re-test the drive with Data Lifeguard. Check cabling and retest.

Unknown symbol on schematic (Circle with "M" underlined) more hot questions question feed about us tour help blog chat data legal privacy policy work here advertising info mobile contact us feedback https://community.wd.com/t/two-brand-new-wd20ears-with-error-code-08/14004 Re-test Drive 150 UNKNOWN ERROR An unknown error has occurred during testing. This may be due to a media error. Replace the drive if the error repeats.

Re-Test Drive 103 Write Fault Error A Write command during the test has failed to complete. navigate here Anyway the drive was not reliable and now it's been replaced. Replace the drive if the error repeats. Replace Drive 225 Too Many Errors Found Error count reached a threshold value.

This may be due to a media error. All Rights Reserved. Contact System Vendor 221 Test Not Supported Certain older drives do not support certain SMART Self Tests. Check This Out The printer may not be attached or turned on.

Replace drive if unable to correct error 120 NO DRIVE FOUND Cannot communicate with drive. Replace the drive if the error repeats. This may be due to a defect.

Platform for OPEN research on Data Recovery !

Re-Test Drive 12 Too Many Bad Sectors Detected Error count reached a threshold value. Re-Test Drive 115 ICRC Error Ultra DMA CRC error. http://support.wdc.com/product/download.asp?groupid=605&sid=3&lang=en It should run from within windows and allow You to test all the hard drives. Retest after checking the connections.

If ECC occurs, use Data Lifeguard repair option for additional error correction. Even though it said SMART passed, it can pass even with some errors. according to web search via google.com ,the minus sign seems to be leftover from "program update": removing error description(s). this contact form Re-Test Drive 356 DAM 1 Data Address Mark.

It also may be due to a defective connection. Auto Offline Data Collection: Enabled. When this occurs, data loss will take place. Got it, continue to print 2012-2016 ManualsLib.com About Us About ManualsLib Privacy Policy F.A.Q.

SCT capabilities: (0x3031) SCT Status supported.