Home > Western Digital > Western Digital Error Code 007

Western Digital Error Code 007

To start viewing messages, select the forum that you want to visit from the selection below. Drive should be replaced. Top michael chiklis Post subject: Re: WD5000AAKX-001CAO Caviar Blue slow sectors issuePosted: June 26th, 2012, 15:22 Joined: December 5th, 2011, 5:38Posts: 995Location: Italy unknown wrote:This problem called : Re-test with appropriate diagnostic utility 222 Drive Failed the Test Self-Monitoring, Analysis, and Reporting Technology (SMART) Error returned during SMART Status/Self Test Command. have a peek here

Re-test Drive with appropriate diagnostic utility 204 Missing Log File The log file that existed at startup of diagnostic utility has been moved or no longer exists. Re-test Drive 137 Relocated Sector Sector Relocated. daringjoe, see above edit. enabled help you monitor a drive's internal status through diagnostic commands. https://support.wdc.com/knowledgebase/answer.aspx?ID=11711

Re-test the drive with Data Lifeguard. Re-test Drive 136 Bad Sector Sector Marked Bad Error. Re-Test Drive 104 Drive Not Ready The drive did not properly respond to test commands. Replace the drive if the error repeats.

This may be due to a defect with the drive or a bad connection. Ask ! Replace the drive if the error repeats. Reports: · Posted 5 years ago Top Mike1030 Posts: 1021 This post has been reported.

This may be due to a media or read/write error. At least ten errors have been detected. The orginal issue was, I have two bootable drives (the other is a Seagate), this problem kepted both drives from booting (not at the same time though). Continued Replace the drive if the error repeats.

Check cabling and retest. This condition occurs when the device's SMART reliability status indicates an impending degrading or default condition. Check Floppy and use appropriate diagnostic utility 207 Critical Resource Error Unable to locate and/or use a system resource (e.g. - printer). It may also happen when the wrong version of diagnostic utility is used.

It is possible the WD drive is more 'picky' on the power, either voltage or amps? recommended you read I had them confirm this. Re-test Drive 213 2-9 DAM Errors Data Address Mark (DAM) 2-9. Local time:02:27 AM Posted 15 April 2013 - 12:29 PM Out standing, then you are good to go.

Replace the drive if the repair fails. navigate here Contact System Vendor 221 Test Not Supported Certain older drives do not support certain SMART Self Tests. Replace Drive 225 Too Many Errors Found Error count reached a threshold value. ReplaceDrive 580 Missing Interrupt An interrupt request failed during the test process.

If this were the case, then I'd say the PSU is at fault? "Switches" inside some ensure proper voltage before it powers up possibly. Some vendors use the security feature to ensure the usage of only specific drives in their system, or the drive may have been locked by a user using a third party This may be due to a media error. Check This Out It also may be due to a defective connection.

The drive may not have been accessed properly possibly due to a bad connection. Retest after checking the connections. Re-Test Drive 10 Set File Pointer Error A SetFilePointer command during the test has failed.

Reply With Quote September 8th, 2008,04:39 PM #2 Train View Profile View Forum Posts Site Moderator Join Date Apr 2000 Location Sheboygan, WI Posts 52,537 0007 = Self Monitoring, Analysis, and

Replace the drive if the error repeats. This may be due to a defect with the drive or a bad connection. System_Memory Test failure Random Hard Drive Failure Opinion on what went wrong (PSU failure) Media Test Failure- Check Cable Video failure? This may be due to a defect with the drive or a bad connection.

Top michael chiklis Post subject: Re: WD5000AAKX-001CAO Caviar Blue slow sectors issuePosted: June 26th, 2012, 13:03 Joined: December 5th, 2011, 5:38Posts: 995Location: Italy I backup all data from Questions: 1. Site Changelog Community Forum Software by IP.Board Sign In Use Facebook Use Twitter Need an account? this contact form CPU Failure?

There were too many errors found on this drive to be repaired. Replace the drive if the error repeats. This is the pretest initialization code which indicates a drive is ready to be tested, but has not yet been tested. This error may have internal and external reasons.

Re-Test Drive 112 IRQ Timeout Interrupt ReQuest Interrupt signal not received. Replace Drive 163 Unknown Error Queued command timed out. Replace Drive 208 SMART status failed after the media scan.