Home > Western Digital > Western Digital Error Codes

Western Digital Error Codes

Contents

No way. Re-Test Drive 109 DRQ WAS SET The drive did not properly respond to test commands. This may be due to an internal error or to a failed connection which did not allow the interrupt command to be sent to the drive properly. Re-test Drive 148 Not Selected Drive not selected. http://3cq.org/western-digital/western-digital-hdd-error-codes.php

Track 0 also holds information about the drive. Drive should be replaced. Several instances of information on data positioning and location could not be found. After generation of RMA, i came across WRITE ZEROS under Windows Data Lifeguard Diagnostics.I did a FULL ERASE using WRITE ZEROS (took about 4 and a half hours), did a WD https://support.wdc.com/knowledgebase/answer.aspx?ID=11711

Western Digital Error Code 0007

Check connections and retest. Drive should be replaced. Ensure that you are using the latest version of diagnostic utility and that your cable is in good working condition.

You may need to rescan to ensure that the repairs were effective. Non-WD drives are not supported. If the errors continue, replace the drive. Re-test Drive with appropriate diagnostic utility 202 Drive Not Supported Older Western Digital drives are not supported by the diagnostic utility version being used.

Re-Test Drive 121 Servo Error Servo error. Data Lifeguard Diagnostic For Dos If the automatic repair feature is unable to repair these errors, replace the drive. Replace Drive 219 Drive Cable Error Failure during cable test. https://support.wdc.com/KnowledgeBase/answer.aspx?ID=654 This may be due to a defect with the drive or the drive may not have responded properly due to a bad connection.

The command set to be executed has timed out. Non-WD drives are not supported. Replace Drive 357 DAM 2-9 Data Address Mark. Replace Drive 223 Errors Repaired Errors found, but have been repaired successfully.

Data Lifeguard Diagnostic For Dos

After that i tested my drive using Diagnostics from WD Smartware. check over here Create and use a new DLG Tools diskette. Western Digital Error Code 0007 There could be media errors present on this drive. Western Digital Support Re-Test Drive 112 IRQ Timeout Interrupt ReQuest Interrupt signal not received.

Please ensure that you are not loading any other DOS level files from the floppy prior to running diagnostic utility. navigate here Re-test Drive 137 Relocated Sector Sector Relocated. This may be an anomaly or a defect with the drive. Replace Drive 215 2-9 IDNF Errors Identified Data Not Found (IDNF) 2-9.

Re-Test Drive 106 Track 0 Error Track 0 was not properly detected. Re-Test Drive 14 Test Suspended A test has been temporarily suspended by the user. Re-Test Drive 356 DAM 1 Data Address Mark. Check This Out Replace the drive.

Drive should be replaced. Replace. Re-Test Drive 108 Seek Not Complete A Seek command did not complete in the time allotted.

Replace the drive if the error repeats.

Check cabling and retest. Please contact the system vendor for the above-mentioned information. Re-Test Drive 116 IDNF Error Address Not Found Error. Replace the drive if the error repeats.

This may be an anomaly or a defect with the drive. Re-Test Drive 258 ECC 10+ Error Correction Code. Please rate the helpfulness of this answer Answers others found helpful Understanding S.M.A.R.T. this contact form If ECC occurs, use Data Lifeguard for additional error correction.

This error is most likely an internal malfunction of the drive and not related to the condition of the cables etc. Replace the drive if the error repeats. Replace the drive if the error repeats. This error may also appear if the floppy has been infected by a hidden virus.

The cable is loose, broken, or not plugged in. Drive should be replaced. In order for S.M.A.R.T. Drive should be replaced.

There may be media errors present on this drive. The same utility and the original code used to lock the drive are necessary to unlock this drive. Version 4.12 for older drives and version 5.00 for current drives.