Home > Western Digital > Western Digital Error Status Code 0201

Western Digital Error Status Code 0201

Re-Test Drive 109 DRQ WAS SET The drive did not properly respond to test commands. Replace Drive 208 SMART status failed after the media scan. Re-Test Drive 6 SMART Diagnostic Self-Test (DST) Failure Self-Monitoring, Analysis, and Reporting Technology (SMART) Self-Test Command failed. Drive should be replaced. have a peek here

If the drive is recognized there, than something is likely wrong with either your power supply, or the data port (or BUS) your drive is being connected to 7. If the errors continue, replace the drive. Re-test Drive 141 UNKNOWN ERROR An unknown error has occurred during testing. ECC is a hardware correction technique that corrects errors. https://support.wdc.com/knowledgebase/answer.aspx?ID=11711

Re-Test Drive 107 Check Sum Error Accumulated test data on the drives is corrupted. CyberDoc LLC 197.269 visualizaciones 13:01 Hard Drive Repair And Data Recovery On 500GB Hard Disk - Duración: 18:28. This may be due to a defect with the drive or a bad connection. Check connections and retest.

Re-test the drive with Data Lifeguard. Apparently I don't have more than 2.6GBs of space available. I've barely had it a week (6 days, MAYBE 7).http://www.newegg.com/Product/Product.aspx?Item=N82E16822136320&cm_re=western_digital_caviar_black-_-22-136-320-_-ProductThere's the link to the product. Please contact the system vendor for the above-mentioned information.

The drive may not have been accessed properly possibly due to a bad connection. Please ensure that you are using the version of diagnostic utility corresponding to either newer or older Western Digital drives. NOTE: Please make sure that you have selected the correct drive to perform this function on as once ran, no data will be recoverable. * VIEW TEST RESULTS - You can http://www.techsupportforum.com/forums/f10/non-wd-drive-error-code-0201-a-151888.html ECC is a hardware correction technique that corrects errors.

Re-test Drive 140 DRQ TIMEOUT ECC The drive did not properly respond to test commands. Cargando... There are too many errors detected on this drive to be repaired. Re-test with appropriate diagnostic utility 222 Drive Failed the Test Self-Monitoring, Analysis, and Reporting Technology (SMART) Error returned during SMART Status/Self Test Command.

It also may be due to a defective connection. I have reset to the default BIOS settings in case they were goofed by the previous owner, and still no success booting from either drive. Drive Reliability Monitor. Cambiar a otro idioma: Català | Euskara | Galego | Ver todo Learn more You're viewing YouTube in Spanish (Spain).

Have you replaced the CMOS battery? navigate here It also may be due to a defective connection. Replace the drive if the error repeats. Boot Issue With HP Pavillion A6142N Started by Smitty, August 28, 2011 8 posts in this topic Smitty 10 Senior Member Registered 10 64 posts Posted August 28, 2011 ·

Retest after checking the connections. It also may be due to a defective connection. All rights reserved Use of this Site constitutes acceptance of our User Agreement (effective 3/21/12) and Privacy Policy (effective 3/21/12), and Ars Technica Addendum (effective 5/17/2012) Your California Privacy Rights The http://3cq.org/western-digital/western-digital-error-status-code-007.php Replace the drive if the error repeats.

The information file, which holds the data pertaining to this drive, is corrupted or missing. Check connections and retest. Test your drive on another system.

Ad Choices d2jspGaming and Trading Community d2jspGaming and Trading Community Hourly Raffle Ladder Slasher Trade Finder Photo Gallery Forum Gold FAQ Instant Messenger Help and Rules Live Streams Account RecoveryResend Validation

It is also possible to see this error on defective Western Digital drives. Retest the drive. Check cable & retest. Please ensure that you are using the appropriate version of diagnostic utility.

Data request has timed out when writing to the drive. Replace the drive if the error repeats. Replace the drive if the error repeats. this contact form Re-test Drive 145 FULL STROKE ERROR Error encountered during full stroke seek.

The BIOS, Phoenix v5.12, sees both the DVD burner and hard drive, but it will not boot from either (I am attempting to boot from an AVG rescue disk). Drive should be replaced. Re-test Drive 220 Drive is Locked Security feature of the drive reports locked status. The same utility and the original code used to lock the drive are necessary to unlock this drive.

I put in my Windows 7 disc, gets to the blue sky background and I can move my mouse around, then nothing. An "Advanced Boot Options" screen opens if the system partition on the hard drive is still good. user-manual-WDH1NC15000N... Drive should be replaced.

Re-Test Drive 356 DAM 1 Data Address Mark. VeRsIoN=7.04 (990819) LaNgUaGe=English (1) SeRiAlNuMbEr=XXXX-0000-654321 This occurs with or without the AVG disc in the DVD drive, and the hard drive is not currently in the tower. 0 Share this post Check your floppy and retest. Password Site Map Posting Help Register Rules Today's Posts Search Site Map Home Forum Rules Members List Contact Us Community Links Pictures & Albums Members List Search Forums Show Threads

You may also want to reroute your IDE cable away from sources of electronic bus noise such as your CPU, Power Supply, etc. PDF Manual Http://pdf.superwarehouse.com/specs/DS... My disc drive works no matter what cord or slot I use, so I think that rules that out. Register Login Posting Guidelines | Contact Moderators Ars Technica > Forums > Hardware & Tweaking > Other Hardware Jump to: Select a forum ------------------ Hardware & Tweaking Audio/Visual Club

greatestunknown 1.294.827 visualizaciones 8:36 Hard Disk Becomes Unallocated - How to Recover Partition with No Formatting (Solved) - Duración: 3:38. A clicking noise can indicate that this error has occurred.