Home > Western Digital > Western Digital Hard Drive Error Code 0132

Western Digital Hard Drive Error Code 0132

You have to be very patient, the quick type scan came up fast with an error (0132) ┬áthen wouldn't let me do anything else. Contact: Contact eviloatmeal Website Re: Diagnosing a Kaput WD External Hard Drive Quote Postby eviloatmeal » Tue Oct 28, 2014 9:16 am UTC Sorry that this isn't actually "helpful" in any Replace the drive if the error repeats. Replace the drive if the error repeats. http://3cq.org/western-digital/western-digital-hard-drive-error-code-0223.php

Drive should be replaced. Re-Test Drive 257 ECC 2-9 Error Correction Code. This may be due to a media or read error. Replace Drive 256 ECC 1 Error Correction Code.

Check cabling and retest. Check cable & retest. Retest. Replace Drive 211 2-9 Uncorr ECC Errors Error Correction Code (ECC) 2 through 9.

This may be due to a defect with the drive or a bad connection. Sense: No additional sense information[ 79.446733] end_request: I/O error, dev sdb, sector 0[ 79.446741] ata1: EH complete[ 79.446964] ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0[ 79.446966] ata1.01: BMDMA This is a monitoring system, which stores all errors, retries, and power on hours. Sense: No additional sense information[ 78.984678] end_request: I/O error, dev sdb, sector 24[ 78.984680] Buffer I/O error on device sdb, logical block 3[ 78.984689] ata1: EH complete[ 78.984770] sd 0:0:1:0: [sdb]

Check connections and retest. I couldn't find a diagnostic tool that listed that exact drive so I DL'd the one that had all the other JD drives on it... Retest and replace the drive if the error repeats. The time now is 02:26 AM. -- Mobile_Default -- TSF - v2.0 -- TSF - v1.0 Contact Us - Tech Support Forum - Site Map - Community Rules - Terms of

then the hard drive spins up, then clicks a few times (louder than usual drive access, usually 3 clicks) then the drive spins down and starts trying to access the floppy This may be due to a media error. Data sent between the host computer and the drive has been corrupted. Re-test Drive 159 SMART Error Self-Monitoring, Analysis, and Reporting Technology (SMART) Error returned during SMART Status/Self Test Command.

There may be repairable media errors on a platter. http://www.motherboards.org/forums/viewtopic.php?t=104651 SERVO is data on track location. It ran about an hour and came up with Error Code 223, and said it repaired all the problems. The same utility and the original code used to lock the drive are necessary to unlock this drive.

Replace the drive if the error repeats. http://3cq.org/western-digital/western-digital-hard-drive-error-codes.php Replace Drive 218 10+ SERVO Errors SERVO 10+. Re-test and Repair Option diagnostic utility 212 10+ Uncorr ECC Errors Error Correction Code (ECC) 10+. Replace the drive if the error repeats.

Re-Test Drive 16 Random Read Error A read command during the test has failed. This may be due to a defect with the drive or the drive may not have responded properly due to a bad connection. Replace the drive if the error repeats. Check This Out Re-test Drive with appropriate diagnostic utility 133 Illegal ID FW overlay not found.

Contact System Vendor 221 Test Not Supported Certain older drives do not support certain SMART Self Tests. Replace the drive if the error repeats. Replace the drive if the error repeats.

The drive has not responded back in the time allotted.

The drive should now be defect free. Paul pbailey Black Belt 1st Degree Posts: 1174Joined: Tue Mar 26, 2002 12:00 amLocation: KC MO WebsiteYIM Top Reply with quote by Karlsweldt » Sat Feb 09, 2008 7:57 am Replace the drive if the error repeats. There are too many errors detected on this drive to be repaired.

On the other hand, if your RAM is still workable, then you just need to increase the size of your page file. Anyway, it won't boot up right, gets to windows basic black screen, or Safe Mode stop at mup.sys area, and stops. Replace Drive 215 2-9 IDNF Errors Identified Data Not Found (IDNF) 2-9. this contact form The drive has to be replaced.

Replace Drive 161 RESET SIGNATURE The drive did not properly respond to test commands. Replace Drive 584 Diag Command Error During a Quick Test, the sefl-test failed. Replace the drive if the error repeats. Retest.

Replace Drive 217 2-9 SERVO Errors SERVO 2-9. Top Jorpho Posts: 5992 Joined: Wed Dec 12, 2007 5:31 am UTC Location: Canada Re: Diagnosing a Kaput WD External Hard Drive Quote Postby Jorpho » Fri Dec 02, 2011 2:47 Retest after checking the connections. Track 0 on the drive must be accessed to perform parts of various internal tests.

If the error repeats, replace the drive. If the system cannot properly handle a drive running a specific Ultra ATA rate such as ATA100, the data may become corrupted. So, I downloaded the WD Data Lifeguard Diagnostic software, had to use the one with the ISO Another anyway, can someone please assist me in figuring out what might be happening, Re-Test Drive 4 Open Drive Failure Cannot communicate with drive.

The failure to complete the test indicates a failed drive. If the automatic repair feature is unable to repair these errors, replace the drive. enabled help you monitor a drive's internal status through diagnostic commands. Ten or more instances of information on data positioning and location could not be found.

Re-test with appropriate diagnostic utility 222 Drive Failed the Test Self-Monitoring, Analysis, and Reporting Technology (SMART) Error returned during SMART Status/Self Test Command. ECC is a hardware correction technique that corrects errors. The command set to be executed has timed out. I have 2 WD hard drives in my studio computer (for music).