Home > Whirlpool Cabrio > Whirlpool Cabrio Dryer Error Codes F31

Whirlpool Cabrio Dryer Error Codes F31


Check for failed belt switch. The first thing you want to do is see if the basket turns freely by hand. Access the thermal cut-off by first removing the back panel. . 3. F20 NO WATER DETECTED ENTERING MACHINE OR PRESSURE SWITCH TRIP NOT DETECTED. this content

Check the electrical connections at the pump and make sure the pump is running. 4. If this doesn't work, and you keep getting the error, you will have to order the position sensor. The failure will be reset after running the Diagnostic Test Program. 1. Show more Language: English Content location: United States Restricted Mode: Off History Help Loading... why not find out more

Whirlpool Duet Dryer Error Code L2

Normal thermistor resistance values: 60° F. - 15.3K ohms. 70° F. - 11.9K ohms. 80° F. - 9.2K ohms. Plug in washer or reconnect power. 4. Check all hoses for possible leaks. 5.

Access the machine control electronics and measure the resistance across P8-4 and P9-1. Refer to the Continuity tests. The duct is clean, too. Whirlpool Cabrio Dryer Troubleshooting Codes Look at each key and try to unstick it.

Click Here to Sign Up! Whirlpool Duet Dryer F 31 Confirm power cord is properly installed and plugged into the outlet. Check valve for continuity (abnormal = infi nity). 2. http://www.appliancepartspros.com/answers-for-whirlpool-control-sahara-de-wpw10174745-ap6016286-question-142452.html Perform TEST #4c.

NOTE: During first power up of new CCU and UI combination, a bootphase (uploading parameters) will be performed. The following table gives temperatures and ranges for the associated thermistor resistance values. The failure will be reset after running the Diagnostic Test Program is run. 1. Activate the diagnostic test mode and advance past saved fault codes. 2.

Whirlpool Duet Dryer F 31

F30 DISPENSER SYSTEM ERROR When the dispenser motor cannot be driven to its proper position. 1. http://www.fixya.com/support/t19681691-whirlpool_cabrio_dryer_error_code_f31 Press PAUSE/CANCEL twice to clear the display. Whirlpool Duet Dryer Error Code L2 If the drum light fails to illuminate, do not assume the machine control electronics needs replacement. Whirlpool Cabrio Dryer F1 Code Top Whirlpool Washing Machines Experts Dan Webster Level 3 Expert 8147 Answers Richard Roth Level 3 Expert 9472 Answers Mike Cairns Level 3 Expert 3053 Answers Are you a Whirlpool Washing

Remove the back panel to access the thermal components. 3. http://3cq.org/whirlpool-cabrio/whirlpool-cabrio-dryer-error-codes-f1.php In normal use (a little blockage is normal) the steamer cleans itself. For SELF CLEAN models: check door lock operation. 3. wtw66005w2 Thank You Is there a number after the F code?Thats ok heres what the code means: Whirlpool Cabrio Washer Fault Codes.Means primary control failure and to resolve this you'll have Whirlpool Cabrio Dryer L2 Code

My name is XXXXX XXXXX I look forward to helping you! Unplug dryer or disconnect power. 2. If failure still present: 3. http://3cq.org/whirlpool-cabrio/whirlpool-cabrio-dryer-error-codes.php Locate the high limit thermostat.

NOTE: To find correct Ohm reading refer to the Water Temperature Sensor section. 1. Replace Central Control Unit if drum is not moving. If failure still present: 3.

This fault code appears ONLY when in the Diagnostic Test Mode.

If there is no water in the unit: Make sure that both valves at the water source(s) are turned on all the way. Check for continuity of the User Interface harness. 2. Perform Service Cycle to pair the UI and CCU SW. 2. Otherwise, go to step 6. 6.

Check the water temperature sensor and connection to it. 3. Short circuit of Heater to Ground. Verify CCU operation by running a Diagnostic Test or any cycle. 3. check my blog NOTE: All thermistor resistance measurements must be made while dryer is disconnected from power.

George Vassallo 101,529 views 9:01 why won't my dryer start? - Duration: 10:24. F-29Moisture Sensor ShortedF-29 flashes when the moisture sensor has shorted. If 5–15 k ohms are measured, replace the machine control electronics. TEST #2 Machine Control Power Check This test is used to determine if power is present at the machine control electronics.

Plug in dryer or reconnect power. 2. Press STOP/CANCEL to clear the display. Enjoy your dinner! Ask Your Own Appliance Question Customer: replied3 years ago. Check resistance of heating element, if present on this model. (abnormal = infinity) 4.

Remember: Oven control (ERC) measures resistance of sensor circuit, not actual oven temperature. At the factory they sprayed a protective coating on them and sometimes this causes the problem. If the above does not correct the problem, go to step 7. 7. Download your simple guide to fixing your non-heating dryer by subscribing to my newsletter.

FdL Door lock error A Door Lock Error occurs if the door cannot be locked. Check the heating coil. If indicators still do not light, the machine control electronics has failed: Unplug dryer or disconnect power. MAIN RELAYS ERROR One of the main relays is not working properly.

Perform test program.