Home > Whirlpool Cabrio > Whirlpool Cabrio Washer F50 Error Code

Whirlpool Cabrio Washer F50 Error Code

Contents

There is no packing materials Expert: JCCARVER replied4 years ago. However the cheaper ones are used http://www.ebay.com/itm/Laundry-Control-W10189966-/140592023082?pt=LH_DefaultDomain_0&hash=item20bbf0062a#ht_2085wt_1163 148.32 for one from what looks like an OK refurb seller I'm going to go for a new one. We are in for over $500 on this repair so far and it still doen't work. Plug in washer or reconnect power. 5. http://3cq.org/whirlpool-cabrio/whirlpool-cabrio-washer-lf-error-code.php

Replace the machine/motor control assembly. Visually check the mounting bracket and electrical connections to the motor and rotor position sensor board. The main control is part number w10189966 and will cost about $200. Also measure the resistance at the P10 connector between pins P10-1 and P10-7 and verify that the resistance is within the range shown in the wiring diagram on page 7-1.

Rotor Position Sensor For Whirlpool Cabrio

If visual checks pass, go to step 6. Watch QueueQueueWatch QueueQueue Remove allDisconnect Loading... This flat rate figure seems over inflated to me.

Fail and it's the motor, Pass and its the control board. by Mark T Earned 26,111 community points in Click'>Washers January 8th, 2012 Comment 0 votes Didn't find what you are looking for? my only guess without probing it would be that the rps is failing, but i'd rather get an expert opinion on it. F50 Error Code Kenmore Oasis See Diagnostic Test for accessing saved fault codes.

Plug in washer or reconnect power. Whirlpool Cabrio Washer Error Code F Pink Frankenstein 8,113 views 2:30 Whirlpool Cabrio F 51 RPS Replacement - Duration: 16:07. Perform steps in Accessing & Removing the Electronic Assemblies, and visually check that the P11 connector is inserted all the way into the machine/motor control. 2. If yes, pump out water.

See Figures 3 and 4, page 6-16. Whirlpool Cabrio Dryer Error Codes Your question was published, help is on its way! Chrome | Firefox | Safari | Internet Explorer Sorry! Worst case I could resell the board on ebay and get my money back if I was wrong.

Whirlpool Cabrio Washer Error Code F

I need help Popular searches Login|Contact Us Appliance Need Appliance Repair Help? Bonuses About a couple years ago I got an f50 error - not spinning or draining. Rotor Position Sensor For Whirlpool Cabrio Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.

LinkBack LinkBack URL About LinkBacks Bookmark & Share Digg this Thread! Whirlpool Cabrio F51 Error Code It spins freely as well.

Ask Your Own Appliance Question Expert: Jon replied4 years ago. news RenewAppliance 96,254 views 2:19 Whirlpool Cabriolet washer F51 code repair - Duration: 2:51. TEST #6 Water Level and Pressure Transducer Calibration This test checks the water level sensing components, and calibrates the pressure sensor. 1. Is the board the only thing left it could be? Whirlpool Cabrio Dryer F50

Loading... I replaced the stator an I still get the same error code. If the water level does not fill to this level, replace the machine/motor control assembly. have a peek at these guys All rights reserved.

The new electronics are not so sensitive and won't F51 easily if it see's a rps position it doesn't loke . Whirlpool Cabrio Diagnostic Mode the following day she decided to wash clothes and an F50 error code was displayed. Activate the Console and Indicators Diagnostic Test mode to verify repair.

Press PAUSE/ CANCEL once to clear the code.

There are no numbers on them and no drawing. Without you wasting $230 on the previous parts. He ordered a replacement sensor and tried to put it in today. Whirlpool Cabrio Control Board If the Manual: Pumps test failed, then the machine/motor control has failed: Unplug the washer or disconnect power.

So I think the motor is OK and it is the motor control board. If visual checks fail, reconnect P5 and P10 and repeat step 1. 6. We took it into the repair shop and had it fixed. check my blog See TEST #3.

Please download one of our supported browsers. ft. Your advise and help is greatly appreciated. About Press Copyright Creators Advertise Developers +YouTube Terms Privacy Policy & Safety Send feedback Try something new!

If the mini-cycle is unsuccessful, uL will flash until the door lid is opened, allowing the customer to view and redistribute the load. You are right Brian, the F50 code isn't about the RPS it's indicative of a failed controller. With the washer off, spin the basket to see if it rotates freely. Remove the console to access the machine/ motor control assembly.

Is the basket floating? If the Diagnostics motor test in step 1 failed, then the machine/motor control has failed: Unplug the washer or disconnect power. Does basket turn freely? Calibrate the pressure transducer: See Activation of Manual Diagnostic Test Mode, and perform steps 1 and 2 until the display shows 00 and the Add A Garment indicator LED is flashing.

read moreReplyDeleteAdd commentLoad more... Are hose screens plugged? Thank you for allowing us to assist you today. > You are a valued Whirlpool customer and we apologize for any inconvenience this concern may have caused. > We invite you F53 (F53) Motor Control Overtemp F then 53 flashes when the machine/motor control detects high temperature for the motor module.

You remove the control panel and ohm out some connectors. Ensure proper hose connections and that household’s hot water is present. 3. I've already replace the sensor and harness and the motor already. http://www.ebay.com/itm/140600823720?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649#ht_499wt_1159 I picked this one because it was new rather than used (more time before this one fails), it was the cheapest new board I could find, and it was on