Home > Whirlpool Cabrio > Whirlpool Error F-1

Whirlpool Error F-1


Check the drive system for any worn or failed components. 5. If you could blow through the hose easily, or you succesfully removed whatever was blocking the hose, reconnect the hose and turn the machine back on. Check wire harness connections to pressure switch, drain pump, and Central Control Unit (CCU). Check the drive system for any worn or failed components and reconnect power and plug unit in. http://3cq.org/whirlpool-cabrio/whirlpool-f51-error.php

E1 Thermistor open Replace thermistor if found defective E2 Thermistor shorted Replace thermistor if found defective WHIRLPOOL FAULT CODES Whirlpool Calypso Automatic Washer Fault Codes Failure Code Fault Code Description Solution F2 will appear. Unplug washer or disconnect power. 3. Honolulu, HI About Us DIY Blog Our Story Core Values Locations Rave Reviews Affiliates Program Job Listings My Account Sign In My Account Order History Shopping Cart Our Policies Terms of

Whirlpool Cabrio F1 Error Code Recall

Remove clothes from drum and start the cycle again. Replace Central Control Unit if drum is not moving F71 USER INTERFACE HEARTBEAT FAILURE If a Central Control Unit Heartbeat Failure is displayed, no communication is detected from the User Interface F99 NOT SUPPORTED User selected on the UI the unsuppor ted Cycle on the CCU. Ft.

Pics 1 and 2: unscrew 3 screws and open the console Verify that the pressure switch hose is hooked up properly. If you don't hear the air, the other end of the hose is probably disconnected from the tub, so try to reconnect it. Sign in to make your opinion count. Whirlpool Dryer F1 Error Code F2 - E1 Keypad cable unplugged F2 - E5 Cancel key drive line open F2 - E6 Cancel key drive line open F3 - E0 Oven temperature sensor (RTD) opened (upper

Check pins 1 and 5 of P16 of the machine controller and pins 1 and 2 of P1 of the motor controller. If you would like to save yourself some trouble, you can take the faster way and repair the machine yourself. Check wire harness connections to the motor, Motor Control Unit (MCU), and Central Control Unit (CCU). useful reference Replace CCU board.

The control must realize that the trip was due to an overfill condition instead of a suds lock condition in order for "FL" to be displayed. Whirlpool Cabrio F1 Recall 2013 Verify that the pressure switch hose is in good condition and properly connected to tub and pressure switch. 1. codes. Check sensor, sensor harness and sensor harness connection at sensor and oven control.

Whirlpool Washer Cabrio Recall

Measure door switch (door open = switch open small low voltage terminals). you could try here Press HOLD TO START to continue the cycle, or press OFF/Pause to clear the display. Whirlpool Cabrio F1 Error Code Recall Joseph Richardson 3,498 views 2:00 Troubleshooting a No-Spin No-Agitate Problem in a Whirlpool VM Washer: Part 2 Conclusion - Duration: 2:23. Whirlpool Cabrio Dryer F1 Check for continuity of the User Interface harness. 2.

Located on the bottom of the door latch assembly is a tear-drop shaped tab. 5. More about the author SL Suds lock The motor controller senses a suds lock condition by analyzing the current draw on the drive motor. Check the MCU by looking for operations of the drive motor. 7. Potential Causes • If there is no water in the unit: - Make sure that both valves at the water source(s) are turned on all the way. - Check Whirlpool Cabrio Control Board

Check that the serial harness at the MCU is not mounted upside down. Verify CCU operation by running a Diagnostic Test or any cycle. 3. NOTE: To find correct Ohm reading refer to the Water Temperature Sensor section. 1. http://3cq.org/whirlpool-cabrio/whirlpool-f50-error.php REPAIR TECHNIQUE 2) According to some repair companies, a possible cause of the F1 error is blockage inside the pressure switch hose.

If ok, replace probe. Whirlpool Cabrio Dryer F1 Error Code Recall If after 30 seconds not minimum 0.1l of water entered or maximum fi ll time of 13 minutes is exceeded, the valves will be turned off and the error code will Thanks and don't give up if your told your machine is not covered...research here, on this Facebook page, and use the power of social media to your advantage!

Check for proper installation, verify the unit is not located near a source of heat and has proper ventilation. 2.

To do this, you will need to purchase a new control board. F1-E3 - Wiring Harness Cavity Size Does Not Match Stored Value - Check the jumpers in the harness to make sure they agree with the actual oven size. F21 LONG DRAIN If the drain time exceeds 8 minutes the water valves turn off. Why Does My Whirlpool Cabrio Washer Says F1 Overloading the unit may cause this problem.

If door not latched: A. Check/clean drain pump filter of foreign objects. 5. Check Pressure Switch for correct working with a DVM/VOM. 3. http://3cq.org/whirlpool-cabrio/whirlpool-ld-error.php Open your washer.

Replace User Interface if drum is rotating. 4. Potential Causes • Check the drain hose and make sure it is not plugged or kinked • Check the electrical connections at the pump and make sure the pump is running. F3 - E1 Oven temperature sensor (RTD) shorted (upper oven, if double oven) F3 - E2 Oven temperature is too high (Cook mode) F3 - E3 Oven temperature is too high Cancel Annie Dorris Rep: 1 Posted: February 9 Options Permalink History What if it just shows an f flashing?

F06 STEAMER DEFECT The Steamer temperature has not reached the correct value. Sud SUDS LOCK (Overdose of detergent detected during the wash cycle) The motor control unit senses a suds lock condition by analyzing the current draw on the drive motor. WTW6400SW2 Anyway this is part of the recall ?Like · Comment · ShareMindy Jordan MarionSeptember 14 at 11:21amWhirlpool your products suck!Like · Comment · ShareCindi PaughSeptember 9 at 11:58amThe bearings are Maybe I can save myself $150 Reply With Quote November 14th, 2010,11:01 PM #6 Jake View Profile View Forum Posts Visit Homepage Appliance Tech - Admin Join Date Aug 2004 Location

If there is an error reading this data it will cause this error. Sign in to report inappropriate content. If after 30 seconds the control does not detect water entering machine and then valves will be turned off and the error code will be displayed. The lid switch must be opened at least once before restarting the cycle, if this condition occurs.