Home > Whirlpool Duet > Whirlpool Error Code 21

Whirlpool Error Code 21

Contents

Press PAUSE/CANCEL two times to clear the display.1. Loading... Sign in 23 Loading... If the distance from the top of the drain hose to the bottom of the washer is more than 96 inches, disconnect the drain hose and place the hose lower on http://3cq.org/whirlpool-duet/whirlpool-f-h-error-code.php

Determined to fix the flashing code I harnessed the power of Google, I quickly found out that the code meant my drain was clogged. ob Off balance If the motor controller detects an unrecoverable off-balance condition, the machine controller will shut down and display an "ob" for off balance. Replace sensor if found defective. So stick around--it should be fun!

Whirlpool Duet Steam F21

Press STOP/CANCEL to clear the display. My wife nylon ‘footie' sock packed its self in that tube, and was easily missed without specific instruction. NOTE: To find correct Ohm reading refer to the Water Temperature Sensor section. 1.

This condition occurs when excessive water in the tub causes the overfill switch to trip. Sud SUDS LOCK (OVERDOSE OF DETERGENT DETECTED DURING THE WASH CYCLE) If suds are detected continuously by the pressure switch during the drain or spin phases, the washer will fill 4 If the drain hose is inserted directly into a drain facility, pull the drain hose out slightly from the drain if pushed too far in to allow for an air gap What Does F21 Mean On A Whirlpool Washer NOTE: Internal metal edges in the washer can be sharp.

Published on Feb 10, 2014Whirlpool washer slow or no drain? Whirlpool F21 Pressure Switch Verify CCU operation by running a Diagnostic Test or any cycle. Here's an excerpt from the service manual on this fault code: EXPLANATION AND RECOMMENDED PROCEDURE F21 LONG DRAIN If the drain time exceeds 8 minutes the water valves turn off. Possible Causes/Procedure Door lock mechanism is broken or removed from door.

I have just done all that and am letting the washer set through the night and then trying to run the clear mode. Whirlpool Duet F21 Pump Possible Causes/Procedure 1. Check door switch contacts. 4. Press PAUSE/CANCEL two times to clear the display.

Whirlpool F21 Pressure Switch

F99 NOT SUPPORTED User selected on the UI the unsuppor ted Cycle on the CCU. http://washerdryerrepairhelp.com/whirlpool-duet-washer-f21-error-fix/ If the condition continues four times, the F31 code will show.MCU FAILURE If the heat sink gets too hot, the Motor Control Unit (MCU) will stop the motor, the MCU will Whirlpool Duet Steam F21 ft. Whirlpool Duet Drain Pump Possible Causes/Procedure Door lock mechanism is broken or removed from door.

Google didn't pop up with any f21 errors that showed the ball valve being a problem. http://3cq.org/whirlpool-duet/whirlpool-f33-error-code.php By the way, when underneath the washer with the front lower panel removed, I actually heard the drain motor (and felt it) turn on. Verify CCU operation by running a Diagnostic Test or any cycle. Just another hose clamp beyond taking the pump out. F21 Whirlpool Duet Washer Pump

Great help. I asked myself if I "…cleaned out all the lines…the long drain line, the pump itself, double checked the impeller, and the short (black rubber corrugated flexible tube leading directly from So, I decided to run a full load on the "normal" setting. http://3cq.org/whirlpool-duet/whirlpool-f-21-error-code.php If during one wash cycle 4 undervoltages occur then a Motor Control Unit failure is displayed. 1.

The control should not allow the unit to run in this condition. F21 Error Code Kenmore Washer Check connection to water heater. 3. Check resistance of heating element, if present on this model. (abnormal = infinity) 4.

Check wire harness connections between the drive motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU). 4.

If no damage to wires and all connectors okay, proceed to step C. Check the drain hose and make sure it is not plugged or kinked. 2. Cleaned out the filter underneath. F21 Error Code Maytag Washer Clear any clog or debris from this area and reassemble the washer.

Check the washer house drain for a clog or restriction. Ran a cleaning cycle and my machine worked great. Replace switch if defective. 4. news Jake Appliance Repair School 1987-1988 Star Appliance Tech. 2 yrs. 1988-1990 Wards Appliance Tech. 11 yrs. 1990-2001 Sears Appliance Tech. 4 yrs. 2001-Oct. 2005 Jake's Appliance Repair Nov. 2005-present Look-Up &

The failure will be reset after running the Diagnostic Test Program. 1. Check for plugged or kinked inlet hoses or plugged screens in the inlet valves. If the condition continues four times, the F31 code will show 1. They use the status lights on the touchpad/LED.

F65 STEAMER TIME OUT REACHED Error happens if there is no communication between Central Control Unit (CCU) and steamer electronic board. Over time I will interject some commentaries to help you better pinpoint the possible cause(s) to your problem. Check wire harness connections to the MCU, the motor, and Central Control Unit (CCU). 4.