Home > Whirlpool Duet > Whirlpool Error F31

Whirlpool Error F31

Contents

Check for plugged or kinked inlet hoses or plugged screens in the inlet valves. Check wire harness connections between the drive motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU). 4. Check mechanical linkage from dispenser motor to the top of the dispenser. 3. Unplug washer or disconnect power. 2. have a peek at these guys

Mesquite, TX "When you say 'Fast Shipping', you aren't kidding!" Warnie M. Check wire harness connections between the drive motor and the Motor Control Unit (MCU), and b etween the MCU and the Central Control Unit (CCU). Check wire harness connections to the door switch/lock unit and Central Control Unit (CCU). 4. Mismatch of User Interface and CCU or corrupted EEPROM. 1. http://producthelp.whirlpool.com/Troubleshooting_Guides/Troubleshooting_for_Dryers_(Front-Load_matching)/Error_Codes/Starts_with_F/F31

Whirlpool Cabrio Dryer Fault Code F31

If "Sud" is displayed a potential suds lock is detected. Unplug washer or disconnect power. 8. Check to see if a household fuse has blown or a circuit breaker has tripped. Thank you Kelly! Expert: Kelly replied3 years ago.

After disconnecting power to the unit, try scraping this coating off the pins. • Check the resistance values between the serial communications pins with the connectors in place. Check the drive system for any worn or failed components. 4. If corrections are made in any step, reconnect power to control. Whirlpool Duet Washer Error Codes F31 C.

Check wire harness connections between the drive motor and the Motor Control Unit (MCU), and b etween the MCU and the Central Control Unit (CCU). How can I get the door to unlock? If the above does not correct the problem, replace the pump. Check the drain hose and make sure it is not plugged or kinked.

Check the drive motor for powered rotations. Whirlpool Cabrio Dryer L2 Error Code Verify wire harness connections to inlet valves, pressure switch, drain pump and Central Control Unit (CCU). 5. NOTE: The door switch/lock unit can be manually unlocked. Replace CCU board.

Whirlpool Duet Dryer Error Code L2

If a failure occurs during high-speed spin, the door will be unlocked after 3 minutes. http://www.justanswer.com/appliance/7s3rm-does-code-f31-mean-whirlpool-cabrio-dryer-moed.html Your Own Question Tyler Z., Appliance Doc Category: Appliance Satisfied Customers: 73493 Experience: 9+ years being an appliance technician with factory training. 13574879 Type Your Appliance Question Here... Whirlpool Cabrio Dryer Fault Code F31 They use the status lights on the touchpad/LED. Whirlpool Duet Dryer F 31 F35 ANALOG PRESSURE SENSOR FAILURE If this failure is displayed, there is any malfunction of the steamer component detected by the Steamer Electronic Board. 1.

If you can print out the last page (page 12) it will be helpful. More about the author F15 Motor Control Unit (MCU) error If the MCU detects multiple resets or errors during a wash cycle it will go into this error mode. Replace User Interface if drum is rotating. 4. Look for welded relay contacts on bake or broil relays. Whirlpool Washer F31 Code

Electronic Board and the valve for steam fill. 4. Ask Your Own Appliance Question Customer: replied1 year ago. This fault code will ONLY appear when in the diagnostic test mode. http://3cq.org/whirlpool-duet/whirlpool-error-f-28.php Remove clothes from drum and start the cycle again.

See service manual for fix. Whirlpool Cabrio Dryer Troubleshooting Codes In normal use (a little blockage is normal) the steamer cleans itself. F25 DRIVE MOTOR TACHOMETER ERROR If the control is unable to properly detect motor speed, the machine shuts down.

Remember: Oven control (ERC) measures resistance of sensor circuit, not actual oven temperature.

CE Communications error If there is any breakdown in communication between the machine controller and the motor controller, "CE" flashes and the unit beeps once. See service manual for fix.F-25Inlet Thermistor ShortedF-25 flashes when the inlet thermistor has shorted. replied5 years ago. Whirlpool Duet Dryer Error Codes It looks like my connections are all tight.

Verify CCU operation by running a Diagnostic Test or any cycle. 6. Check the pressure switch. 8. Nest® and Nest Learning Thermostat™ are trademarks licensed by Nest Labs, Inc. news rL LOAD INSIDE DRUM DURING CLEANING WASHER CYCLE If at the start of the CLEANING WASHER cycle a load is detected inside the drum.

Door not opened during 3 consecutive cycles. 1. Unplug washer or disconnect power. 2. Potential Causes • If too much detergent was used, run the unit through a Rinse/ Spin cycle then a Normal cycle without adding any detergent. Sarasota, FL "Best customer service experience I ever had." Christine G.

I haven't heard from you since last Thursday. Check doorswitch system. (See checklist of F26 and F29). Plug in washer or reconnect power. 4. Check the drive motor for powered rotations.

And you have to test for voltage on the control board WITH the Red wire off the black square relay if not when you turn the dryer on the Black square NOTE: During first power up of new CCU and UI combination, a bootphase (uploading parameters) will be performed. Check wire harness connections to the dispenser motor and Central Control Unit (CCU). 4. Verify CCU operation by running a Diagnostic Test or any cycle.

F31 MCU FAILURE If the heat sink gets too hot, the Motor Control Unit (MCU) will stop the motor, the MCU will communicate this failure to the Central Control Unit (CCU), Unplug washer or disconnect power. 3. ob Off balance If the motor controller detects an unrecoverable off-balance condition, the machine controller will shut down and display an "ob" for off balance. If failure still present: 3.

Check wire harness connections between the drive motor and the Motor Control Unit (MCU), and b etween the MCU and the Central Control Unit (CCU). DDE 5300 10/30/2016 10/30/2016 centralappliance1 I have a Samsung front loading dryer and there is a symbol 10/25/2016 10/25/2016 md20/20 We have a Kenmore Model 111.66002011 electric dryer. If there is water in the unit: Verify that the pressure switch hose is in good condition and properly connected to tub and pressure switch. 1. B.

F20 NO WATER DETECTED ENTERING MACHINE OR PRESSURE SWITCH TRIP NOT DETECTED. test L1 Black and L2 Red at the terminal block and turn the unit on and try to start it! FdU Door unlock error A Door Unlock Error occurs if the door cannot be unlocked.