Home > Whirlpool Duet > Whirlpool Washer Error Codes E2

Whirlpool Washer Error Codes E2

Contents

F2 will appear. I reconnec... FdL - Door Lock Error - It is possible the door lock mechanism is broken or removed, or the door switch/lock unit has failed. Check wire harness connections to pressure switch, drain pump, and Central Control Unit (CCU). http://3cq.org/whirlpool-duet/whirlpool-washer-error-codes-f21.php

Rescue Movers 3,199 views 3:41 Washer Temperature Sensor Replacement – Whirlpool Front-Load Washer Repair (Part #W10442461) - Duration: 3:00. Allow at least a minute after power has been restored and if error code reappears, replace control board (clock). Flashing display time Open lid If the lid opens while the unit is in running mode, time remaining will flash in the display. FdL Door lock error A Door Lock Error occurs if the door cannot be locked.

Whirlpool Duet Dryer E2 Error Code

Also check for any causes of high resistance in the oven temperature sensor circuit. Replace failed component. Loading...

CST Sat 7:00 a.m. - 9:00 p.m. Jake Appliance Repair School 1987-1988 Star Appliance Tech. 2 yrs. 1988-1990 Wards Appliance Tech. 11 yrs. 1990-2001 Sears Appliance Tech. 4 yrs. 2001-Oct. 2005 Jake's Appliance Repair Nov. 2005-present Look-Up & All rights reserved. E2 F3 Error Code Whirlpool Oven CA or CI Average current limit or Instantaneous current limit If a status signal comes back from the motor controller that a current limit has been breached, the unit will return

Opening the lid will allow you to redistribute the load to avoid a further off balance error. Whirlpool Duet E2 F5 I read about it here at MML, howerver the information represented a Kenmore 2 answers Related Questions'>Kenmore front load washer #11045862400: I have replaced two belt, but they keep comming off Loading... Replace failed component.

Check the drive belt and reconnect power and plug unit in. Whirlpool Duet F2 E3 codes except F1-E3. If the dryer does not heat the thermal fuse should be checked before replacing the heating element. It will try to unlock the door 6 times before displaying the error.

Whirlpool Duet E2 F5

Get more answers from the people in your networks Tags Washers Click to remove this tagging. http://www.appliancepartspros.com/repair-help/whirlpool-fault-codes.html Sr Stuck relay "Sr" signifies a failure of the relay in the closed position. Whirlpool Duet Dryer E2 Error Code Buy the new Duet Washer Water Temperature Sensor WPW10467289 http://www.appliancepartspros.com/whi... F3 E2 Error Code Whirlpool Duet Gas Dryer Troubleshooting Dryer Takes Too Long to Dry Clothes?

If the thermistor is defective, it may prolong or shorten the drying time or cause a fault code. More about the author Open the lid or press STOP/CANCEL to clear the display. OK, Continue Tips for finding your unique model number Look for your model sticker, tag or plate. F7-E1 - Common Switch Wire Is Defective - This error occurs when common wire to latch switch and door switch is shorted. Whirlpool Duet Water Temperature Sensor

Make sure the harness does not have a bad connection. • Check the quick disconnect at the motor terminal. F2-E5 - Cancel Key Line Open - Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure. If damage is found, replace appropriate part. http://3cq.org/whirlpool-duet/whirlpool-washer-error-codes-f28.php If this happens, replace oven control (also called clock or ERC). 2.

It will try to lock it 6 times before displaying the error. Air Conditioning Code E2 Error Also check the heating element to be sure it has continuity. If corrections are made in any step, reconnect power to control.

Check wire harness connections to the motor, Motor Control Unit (MCU), and Central Control Unit (CCU).

Check wires and connectors from control to latch switch, then from latch switch to control. The unit will attempt the clean out the suds three times before displaying this error. Most orders delivered in 2 business days or less.Tools needed: Torx 20 screwdriver.This Whirlpool made Duet Washer Water Temperature Sensor replaces the following older part numbers: W10467289, 8181705, 8182291, 8540225, 8540226. F3 E2 Error Code Maytag Washer Potential Causes • Check Wire Harness connections to the MCU, the motor, and Central Control Unit (CCU) • Check the Drive system for any worn or failed components • Check MCU

Find Parts ^ top Appliance Repair Appliance Repair Dishwasher Repair Garbage Disposer Repair Dryer Repair Freezer Repair Microwave Repair Range / Oven Repair Range Hood Repair Refrigerator Repair Trash Compactor Repair Recently Visited () Getting your parts... 24/7 Customer Support Call 1-877-477-7278 Sign In About Us Repair Forum My Account Order Status Shop for Parts Get Repair Help CHECKOUT Items in Cart: the temperature sensor is at the bottom back of the tub. news Loading...

F1-E4 - Model ID Error - Disconnect power for at least 30 seconds and then reconnect. Logged AJ TechnicianAdministrator Member Since: Jun 2007 Posts: 10511 Country: Re: Whirlpool washer WFW92500WW00 with E2-F3 error code « Reply #7 on: December 10, 2014, 07:08:00 PM » Logged Ajbiomed For SELF CLEAN models: check door lock operation. 3. i regret to hear that you are having issues with your washerand do understand your frustration.

Cabrio® Top ... Remember: The oven control board (clock) measures resistance of sensor circuit, not actual oven temperature. Er - Processor Reset Error - This error will only occur if the unit fails to save cycle information during a power outage. Opening the lid will allow you to view and redistribute the load.

Once the F2 code appears, select 'cancel' and observe for one minute for errors.